Led

msp430f169读写SD卡，文件系统是FAT16(msp430f169 SD card reader, the file system is FAT16)

msp430f5438系统中文资料(全)(msp430f5438system_Chinese Materials)

This software is an example to use Picoscope 3306 DC generator to drive an old Heater.

freescale MCU,S12G128的ADC模块与PWM模块的使用，通过电位器模拟电压输入，控制PWM的占空比输出，可以控制LED灯、电机驱动等任务。(freescale MCU S12G128 ADC module and PWM module, an analog signal input control the PWM duty)

永磁同步电机无传感器矢量控制方法研究及仿真(Research sensorless vector control methods and simulation of permanent magnet synchronous motors)

说明：  msp430g2553使用1306显示超声波测距(2553 Displays Ultrasound Ranging by 1306)

使用MSP430F5438单片机和HC-SR04超声波模块实现测距的源码。( Using the MSP430F5438 microcontroller and HC-SR04 ultrasonic ranging module source.)

自动点击辅助 自动点击辅助自动点击辅助自动点击辅助(Click on the auxiliary automatically )

说明：  GD32 SPI 主从通信，通过片选IO启动传输，单次最大传输64K(GD32 SPI master-slave communication)

STM32作为主控芯片，72Mhz，利用DMA+PWM实现驱动WS2812，创建16个并行800kBit / s数据流的想法如下： 使用定时器每1.25us创建一个800kHz的时基和一个DMA请求。 使用2个比较模块在低位时间（350ns）和高位时间（700ns）下创建DMA请求 1.25us DMA请求将GPIO端口的所有位设置为高电平 350ns DMA请求将数据从帧缓冲区传输到GPIO端口。如果该位为0，GPIO引脚将变为低电平，否则将保持高电平。 700ns DMA请求将所有GPIO引脚设置为低电平。 重复步骤1到3，直到发送所有位。 这产生脉冲周期为1.25us，脉冲宽度为350ns或700ns的脉冲流，具体取决于脉冲表示的位值，通过DMA将数据传输到GPIO端口意味着每16个LED每位需要一个字（两个字节）。每个LED 24位，每16个LED 24个字（48个字节）。(The idea to create 16 parallel 800kBit/s data streams is the following: Use a Timer to create an 800kHz time base and a DMA request every 1.25us. Use 2 compare modules to create DMA requests at the low bit time (350ns) and the high bit time (700ns) The 1.25us DMA request sets all bits of the GPIO port high The 350ns DMA request transfers the data from the frame buffer to the GPIO port. If the bit is a 0, the GPIO pin will go low, otherwise it will stay high. The 700ns DMA request sets all GPIO pins low. Repeat steps 1 to 3 until all bits have been transmitted. This creates a stream of pulses with a pulse period of 1.25us and a pulse width of either 350ns or 700ns depending on the bit value the pulse represents. Transferring the data via DMA to the GPIO port means that per 16 LEDs one half word (two bytes) is needed per bit. At 24 bits per LED that makes 24 half words (48 bytes) per 16 LEDs.)