粒子群算法之一，可在matlab中运行-PSO

这个m文件实现了Newton raphsom算法，从而解决分布式功率流问题。(M realized this document Newton raphsom algorithm, so as to solve the problem of distributed power flow.)

基于二维自适应异小波基小波变换的规则纹理缺陷检测(Texture defect detection based on the rule of two-dimensional adaptive wavelet transform different wavelet)

说明：  practical work shop in C/C++

multivariate analysis tool

说明：  基于神经网络的预测方法，可用于光伏预测，拟合较好(BP forecast based on Matlab)

说明：  ex4_2 用MATLAB作巴特沃斯低通滤波器设计 ex4_3 用MATLAB作切比雪夫-1型低通滤波器设计 ex4_4 切比雪夫-2型低通滤波器设计 ex4_5 椭圆型低通滤波器设计 ex4_6 传递函数的模拟滤波器数字化 ex4_7 脉冲不变法简单实例 ex4_8 脉冲不变法巴特沃思低通滤波器设计 (ex4_2 using MATLAB for Butterworth low-pass filter design using MATLAB for ex4_3 Chebyshev-1-type low-pass filter design ex4_4 type-2 Chebyshev low-pass filter design ex4_5 elliptic low-pass filter design ex4_6 transfer function digitization of analog filters ex4_7 the same method is simple example of pulse-pulse unchanged law ex4_8 Butterworth low-pass filter design)

用matlab编程，RBF用聚类方法求中心时的程序(Using matlab programming, RBF centers seeking clustering method using the procedure)

对双极性随机序列二进制数字基带信号，采用开方升余弦滚降波形、矩形脉冲、半波正弦在白噪声条件下的最优（匹配滤波器）接收程序。考察码间串扰和白噪声共同作用引发的误码，画出误码率曲线；设计均衡器画出误码率曲线。(Bipolar random sequence of binary digital baseband signal, using the square root raised cosine wave, rectangular pulse, half sine wave white noise under optimal conditions (matched filter) receiver. Crosstalk and white noise error caused by interaction between the inspection code, drawn BER curves design equalizer to draw BER curves.)

最速降模型是泛函分析中的一个经典问题，这里给出了求解该问题的Matlab解法。(Steepest Descent Method)

说明：   该电路由一片四双向模拟开关集成电路CD4066为核心构成。每个电路内部有四个独立的能控制数字或模拟信号传送的开关。当水箱无水时，由于180K电阻的作用，使四个开关的控制端为低电平，开关断开，LED 不发光。随着水位的增加, 由于水的导电特性，使得IC的13脚为高电平，S1接通，LED1点亮。当水位逐渐增加时，LED依次发光指示水位。水满时， LED4发光， 显示水满。同时T1导通， B发出报警声，提示水已满。不需要报警声时，断开开关K即可。 (The circuit consists of a four-way analog switch integrated circuit CD4066 core composition. Within each circuit to control four separate digital or analog signal transmission in the switch. When the tank water, the role of the 180K resistor, so that the four low-side switch control, switch off, LED does not light. As the water level increases, the electrical properties of water, making the IC' s 13 feet high, S1 connected to, LED1 lights up. When the water level gradually increased, LED turn light level indication. Is full of water, LED4 LED display full of water. At the same time conducting T1, B alarm will sound, indicating that the water is full. Do not need to sound the alarm when the disconnect switch K can be.)