基于Mesri蠕变模型的桥梁桩基工后沉降计算程序

一个比较典型的PID处理程序，在使用单片机作为控制cpu时，请稍作简化，具体的PID 参数必须由具体对象通过实验确定。由于单片机的处理速度和ram资源的限制，一般不采用浮点数运算， 而将所有参数全部用整数，运算到最后再除以一个2的N次方数据（相当于移位），作类似定点数运算，可 大大提高运算速度，根据控制精度的不同要求，当精度要求很高时，注意保留移位引起的“余数”，做好余 数补偿。这个程序只是一般常用pid算法的基本架构，没有包含输入输出处理部分。 (A typical PID process, using the microcontroller as a control cpu, make some simplification, the specific PID parameters must be determined experimentally by a specific object. As the chip processing speed and ram resource constraints, generally do not use floating-point operations, and all parameters of all integers, and divided by an operator to the last N-th power of 2 data (the equivalent of the shift) for a similar fixed-point operations, can greatly improve the speed of operation, according to the different requirements of precision control, when high precision, attention to retain the shift caused by the " remainder" and on the remainder of compensation. This procedure is commonly used basic structure pid algorithm, does not include input and output processing section.)

求最短路问题，matlab程序可运行，还有word详细讲解最优截断切割(Seeking the shortest path problem, matlab program can be run, as well as the word explain in detail the optimal cut-off cutting)

二次采样以确定像素间的相关性，然后对两个采样结果同时嵌入水印，利用的是倒谱变换(second sampling to determine the correlation between pixels, then the two sampling results also embedded watermark, make use of Cepstrum)

MATLAB 程序设计语言基础,基本数学运算,MATLAB语言流程控制,函数编写与调试,二维图形绘制,三维图形表示,MATLAB语言与现代科学运算. (MATLAB language process controlling)

THIS IS A LEACH PROTOCOL

说明：  PSO优化算法优化多变量没别的了，就这样了了了了了了(PSO optimization algorithm)

说明：  使用叶素动量理论（BEM）设计风力机叶片(Design of wind turbine blade based on BEM)

在matlab环境下编写的支持向量机代码，简单易懂(SVM-code, easy to learn the code for two types of classification)

Atmosphere model for 200km

设计一个8阶以内的带通滤波器，通带截止频率fc1=30070HZ，fc2=32170HZ，通带内允许最大衰减0.2dB。设计满足要求的Butterworth滤波器和chebyshev滤波器。以RC运放为基本单元以最易实现的原则完成电路设计及参数选择，并根据设计参数进行幅频特性和相频特性的仿真，给出仿真曲线。分析电路的无源灵敏度。(Design within an 8-order band-pass filter, the passband cutoff frequencies FC1 = 30070HZ, FC2 = 32170HZ allow maximum attenuation 0.2dB within the passband. Designed to meet the requirements of the Butterworth filter and chebyshev filter. RC op amp is the basic unit is the most easy to implement the principle of complete circuit design and parameter selection, and in accordance with the design parameters of the amplitude-frequency characteristics and phase-frequency characteristics of the simulation, simulation curve. Passive sensitivity of the analysis circuit.)