从零教你LabVIEW仪器控制

Labview读取Excel，写入Excel(Labview reads Excel and writes Excel)

LabView新型控件，界面华丽，适合自己开发使用。(new defination of LabView such as an important thing in the )

说明：  使用labview实现波形包络检波，可以当子VI使用(Using LabVIEW to realize waveform envelope detection can be used as sub-VI)

电机控制，位置控制，速度控制，反馈控制/..............(motion control)

滚动轴承的故障诊断程序，可实现在线诊断和自动识别(Rolling bearing fault diagnosis)

labview的PXI应用实例，通过工程实例详细介绍了PXI虚拟仪器的使用。(PXI using in labview)

基于LabvIEw的通用自动测试系统(ATs)舍计算机，可鳊程激励、响应数据采集及uuT模块，采用MxI总线控制方式。专用信号发生器为uuT提供模拟激励信号，矩阵开关和适配器完成不同信号间切换。主控计算机执行测试程序，信号发生器发送激励信号，数据采集卡采集数据，采集数据经调理后，并与标准数据|匕较是否满足相应测试结果。(The general automatic test system (ATs) based on LabvIEw can be used as a computer to excite, respond to data acquisition and uuT module. The control mode of MxI bus is adopted. Special signal generator provides analog excitation signal for uuT, matrix switch and adapter complete switching between different signals. The main control computer executes the test program, the signal generator sends the excitation signal, the data acquisition card collects the data, after the data acquisition is adjusted, and compares with the standard data | dagger whether it meets the corresponding test results.)

说明：  该源代码是基于车载平台上的通讯诊断协议， 能够利用LabVIEW, LabWindows?/CVI, Visual C/C++ 6.0中基于CAN的汽车诊断 兼容Windows 7/Vista/XP/2000和LabVIEW Real-Time 诊断协议:CAN (ISO 15765, OBD-II)的KWP2000 (ISO 14230)和诊断 (Diagnostics) 传输协议:ISO传输协议15765-2和Volkswagen TP 2.0 兼容的接口:NI-XNET CAN、CompactRIO CAN、USB CAN和Series 2 NI CAN (PXI、PCI、PCMCIA) KWP2000和UDS的范例, 包括一个软件ECU仿真器(The source code is based on the communication diagnosis protocol on the vehicle platform. Auto diagnosis based on C AN in LabVIEW, LabWindows (/ CVI), Visual C/C++ 6.0 Compatible with Windows 7/Vista/XP/2000 and LabVIEW Real-Time Diagnostic protocols: KWP2000 (ISO 14230) and Diagnostics of CAN (ISO 15765, OBD-II) Transport protocol: ISO transport protocol 15765-2 and Volkswagen TP 2.0 Compatible interfaces: NI-XNET CAN, CompactRIO CAN, USB CAN and Series 2 NI CAN (PXI, PCI, PCMCIA) Examples of KWP2000 and UDS, including a software ECU emulator)

电机控制的一部分程序 还没有编完 以后陆续上传完整程序(Simulation odule unctions)

本人是刚刚学习的小菜鸟，根据网络教程做了一个关于串口的调试程序(Debug the serial port)