avrdudeprog33

说明：  STC8F2K64S2系列单片机提供16个中断请求源，分别是：外部中断0中断（int0）、定时器0中断（timer0）、外部中断1中断（int1）、定时器1中断（timer1）、串行端口1中断（uart1）、低压检测中断（lvd）。，串行端口2中断（UART2），串行外围接口中断（SPI），外部中断2中断（INT2），外部中断3中断（INT3），定时器2中断（Timer2），外部中断4中断（INT4），定时器3中断（Timer3），定时器4中断（Timer4），比较器内部PT（CMP），I2C总线中断。除了外部中断2、外部中断3、定时器2中断、定时器3中断、定时器4中断和比较器中断固定是最低优先级中断外，所有其他中断都有四个可设置的中断优先级。(STC8F2K64S2 series single chip microcomputer provides 16 interrupt request sources, which are: external interrupt 0 interrupt (INT0), timer 0 interrupt (Timer0), external interrupt 1 interrupt (INT1), timer 1 interrupt (Timer1), serial port 1 interrupt (UART1), low voltage detection interrupt (LVD), serial port 2 interrupt (UART2), serial peripheral interface interrupt (SPI), external interrupt 2 interrupt (INT2), external interrupt 3 interrupt (INT3), Timer 2 interrupt (Timer2), external interrupt 4 interrupt (INT4), timer 3 interrupt (Timer3), timer 4 interrupt (Timer4), comparator interrupt (CMP), I2C bus interrupt. Except that the external interrupt 2, the external interrupt 3, the timer 2 interrupt, the timer 3 interrupt, the timer 4 interrupt and the comparator interrupt fixed are the lowest priority interrupts, all the other interrupts have four interrupt priorities that can be set.)

用labview读取dxf文件的案列，labview是面向工程师的语言(Using LabVIEW to read the column of the DXF file, LabVIEW is an engineer oriented language)

说明：  基于卡尔曼滤波和最近邻法的多目标跟踪算法(multiple target tracking in Nearest Neighborhood Classifier)

说明：  生成gps L1 c/a码,并仿真生成gpsL1信号,增加高斯白噪声(GPS L1 C / a code is generated, and gpsl1 signal is generated by simulation to increase Gaussian white noise)

j2me版本的俄罗斯方块游戏源码，运行在诺基亚手机中的Java小游戏，兼容西门子手机，代码简单，学习Java游戏编写的可参考下。

在MATLAB环境中的WCDMA Design using Simulink,和功能演示.对做第三代移动通信仿真非常有用-in MATLAB environment WCDMA Design using Simulink. and functional demo. right to do the 3rd Generation Mobile Communication Simulation very useful

很好用的代码 简单操作 且是用R语言编写 真的很好用啊( Conceptually, this is a good model, but all too often people actually implement their code this way.)

神经网络控制，基于matlab编程算法。可以学习借鉴使用(Neural network control, based on MATLAB programming algorithm. You can learn from it.)

说明：  利用神经网络算法进行负荷的预测，选取若干天的预测数据，来预测接下来几天的负荷数据(The neural network algorithm is used to forecast the load. The forecasting data of several days are selected to forecast the load data of the next few days)

matlab程序，基于最小均方误差准则和线性约束最小方差准则的自适应波束形成。(Adaptive beamforming based on MSE(Mean Square Error) and LCMV(Linear Constraint Minumum Variance),based on Matlab)