wogan

文具体介绍了有关投影法进行字符分割的程序源码(Text details for the projection of the program source code character segmentation)

提出了一种求解电磁场有限元 边界元混合法所生成的线性方程组的有效方法 ———内观 法结合多波前法.由于该线性方程组的系数是一个部分稀疏部分满填充的矩阵,为了加速求解,应用内观法将系数矩阵分为 2块,一块是有限元法形成的稀疏矩阵,另一块是边界元法生成的满阵,然后用多波前法求解稀疏矩阵方程,用高斯 约当消去法解满阵方程. 采用该方法,计算了二维多层介质柱体的雷达散射截面.计算结果表明,该方法的计算效率远远高于传统的高斯法.(Proposed for solving mixed finite element boundary element linear equations generated by an effective method of Vipassana--- a combination of multi wave front method. Since the coefficients of linear equations is a part of the sparsely populated part of the full matrix, in order to speed up the solution, application of Vipassana coefficient matrix is ​ ​ divided into two, one is the finite element method for the formation of the sparse matrix, the other is the boundary element method generates the full array, and then use the multifrontal method for solving sparse matrix equation Gauss Jordan elimination method with full matrix equation solution. use this method to calculate the two-dimensional multi-layer dielectric cylinder of the radar cross section. The results show the computational efficiency of this method is much higher than the traditional Gaussian law.)

倒立摆控制系统是一个复杂的、不稳定的、非线性系统，是进行控制理论教学及开展各种控制实验的理想实验平台。对倒立摆系统的研究能有效的反映控制中的许多典型问题：如非线性问题、鲁棒性问题、镇定问题、随动问题以及跟踪问题等。通过对倒立摆的控制，用来检验新的控制方法是否有较强的处理非线性和不稳定性问题的能力。利用模糊控制对倒立摆进行控制(Inverted pendulum control system is a complex, unstable, nonlinear system, which is an ideal experimental platform for teaching of control theory and various control experiments. The research of inverted pendulum system can effectively reflect many typical problems in control, such as nonlinear problem, robust problem, stabilization problem, follow-up problem and tracking problem. Through the control of the inverted pendulum, used to test whether the new control method has a strong ability to deal with nonlinear and instability problems. The fuzzy control is used to control the inverted pendulum)

说明：  通过 matlab 编程实现捷联惯导系统初始对准、惯导解算的全过程。 1）初始自对准：利用前10分钟实验车静止的数据进行惯导系统的自对准。采用前2分钟数据进行解析粗对准，后8分钟数据用五状态Kalman滤波器实现精对准；为了验证精对准性能，可在粗对准结果上把航向角人为加一定幅度（如10度）的误差，观察精对准的收敛性能。 2）纯惯导解算：对准结束后转入纯惯性导航解算，要求进行双子样的圆锥和划摇补偿，即每20ms完成一次导航解算，输出完整的导航结果包括三个姿态、两个水平速度和两个水平位置（天向通道发散不必输出），并给出姿态、速度、位置随时间的变化曲线以及位置误差曲线。(The whole process of initial alignment and inertial navigation solution of strapdown inertial navigation system is realized by matlab programming.)

2D_ watermarking source image to wartermarking image

说明：  此程序中将两个离散时间信号卷积，在数字信号处理过程中很有用！(conversion)

基于cs的稀疏信道估计算法原理即MATLAB程序(Cs based on the principle of sparse channel estimation algorithm that MATLAB program)

matlab编写的盲信道估计程序，对进行信道估计的朋友有用。(matlab prepared blind channel estimation procedures, the channel estimation friends helpful.)

基于MATLAB的系统分析与设计：信号处理 楼顺天 等编(System analysis and design based on MATLAB: signal processing Lou Shuntian edited)

sample of assembly language for beginners...