充电盒

说明：  熟悉pic控制12864 LCD的使用方法 LCD循环显示本站网址和电话 硬件要求：LCD直接与单片机的A口和D口相连接所有拨码开关置OFF (Familiar with the pic to control the use of 12864 LCD cycle LCD display site URL and phone hardware: LCD directly with the MCU and D I A I connected all the allocated code switch OFF Purchase)

kingview and 51MCU ASCII send and recieve 组态王与51单片机通信ASCII(kingview and 51MCU ASCII send and recieve)

说明：  基于SPMC75的变频电机驱动例子,相当于一个简单的变频器. 望对变频器开发的工程式师有一定的帮助!(SPMC75 based on the frequency motor drive examples, the equivalent of a simple inverter. look for the development of inverter-type division works can help!)

单片机键盘控制代码，适用于凌阳51系列单片机(SCM keyboard control code for Sunplus 51 series)

实验器材: MiniSTM32F103开发板V3版本 实验目的: 学习VS1053的使用,实现一个简单的MP3. 硬件资源: 1,DS0(连接在PA8) 2,串口1(波特率:9600,PA9/PA10连接在板载USB转串口芯片CH340上面) 3,ALIENTEK 2.8/3.5/4.3/7寸TFTLCD模块(通过GPIO驱动,连接关系见lcd.h) 4,W25Q64(SPI FLASH芯片,连接在SPI1上) 5,按键KEY0(PC5)/KEY1(PA15)/KEY_UP(PA0,也称之为WK_UP) 5,SD卡,通过SPI1连接 6,ATK-VS1053模块与STM32芯片连接关系为(请按如下接线连接Mini板和MP3模块): ATK-VS1053模块----------STM32芯片 VS_SCK ----------- PA5 VS_MISO ------------ PA6 VS_MOSI ------------ PA7 VS_RST ------------ PA11 VS_XDCS ----------- PA4 VS_XCS ----------- PA8 VS_DREQ ------------ PA12 5V ------------ 5V GND ------------ GND(Laboratory equipment: MiniSTM32F103 Development Board V3 Version The purpose of the experiment is: Learn the use of VS1053 and implement a simple MP3. Hardware resources: 1, DS0 (connected to PA8) 2. Serial port 1 (baud rate: 9600, PA9/PA10 connected on board USB to serial chip CH340) 3, ALIENTEK 2.8/3.5/4.3/7 inch TFTLCD module (driven by GPIO, connection relationship see lcd.h) 4, W25Q64 (SPI FLASH chip, connected to SPI 1) 5. Keyboard KEY0 (PC5)/KEY1 (PA15)/KEY_UP (PA0, also known as WK_UP) 5, SD card, connected by SPI1 6. The connection relationship between ATK-VS1053 module and STM32 chip is as follows (please connect Mini board and MP3 module according to the following wiring): ATK-VS1053 Module - ----- STM32 Chip VS_SCK------------- PA5 VS_MISO---------------- PA6 VS_MOSI---------------- PA7 VS_RST---------------- PA11 VS_XDCS------------- PA4 VS_XCS--------------- PA8 VS_DREQ---------------- PA12 5V--------------- 5V GND--GND)

说明：  串口控制c源代码，自己看看，根据例程改的(Serial port control C source code)

It do the decoupled load flow in power system

叫你如何用dave设置！！经验证可以通过！用的MCU是英飞凌的XC886!(Dave told you how to set up! ! Proven by! MCU is used Infineon XC886!)

说明：  四个舵机的键盘输入控制，需要使用arduino的串口通讯和串口监视(Keyboard input control of the four steering engines requires the use of arduino serial port communication and serial port monitoring)

直流有刷电机驱动程序，基于STM32F4(DC brush Motor Driver code, based on STM32F4)