ComputerSetTimePowerOff

stm32F103c8t6 连接HC08蓝牙串口模块与手机（安卓系统）通过蓝牙连接，并实现手机无线控制stm32F103c8t6 的GPIO口控制指示灯动作，同时stm32F103c8t6 的GPIO口控制指示灯动作后将指示灯状态通过HC08蓝牙模块回传给手机APP，并在APP上显示出来。(Connect the HC08 stm32F103c8t6 Bluetooth serial module and mobile phone (Android) via Bluetooth, mobile phone and wireless control stm32F103c8t6 GPIO port control indicator action, while the stm32F103c8t6 GPIO port control indicator after the action will light status through the HC08 Bluetooth module back to the mobile phone APP, and displayed on the APP.)

本项目是基于Cortex-M3 的地沟油快速检测装置，旨在实现“地沟油”快速，现场检测。MCU控制可编程的直接数字频率合成器（DDS）产生正弦激励信号，经过可变增益放大器（VGA）和低通滤波器（LPF）作用于食用油阻抗传感器（实验室制作）信号经过仪器放大器送入微控制器（MCU）的模数转化（ADC）通道，MCU对采集的信号通过快速傅里叶变换（DFT）处理，实现食用油阻抗与相角的检测；USB和以太网接口，可与计算机通讯，以便对采集的数据进行存储和分析。(The project is based on the Cortex-M3 waste oil rapid detection device designed to achieve " waste oil" rapid, on-site testing. MCU control programmable direct digital frequency synthesizer (DDS) generates sinusoidal excitation signal through a variable gain amplifier (VGA) and a low-pass filter (LPF) acting on the oil-impedance sensor (lab produced) to send signals through the instrumentation amplifier into the microcontroller (MCU) modulo conversion (ADC) channels, MCU signal acquisition via Fast Fourier Transform (DFT) processing, oil resistance and phase angle detection USB and Ethernet interfaces, and computer communication, in order to collect data for storage and analysis.)

This source code provides a tool to convert .hex files cyrpess programs to uploadable cyacd programs. These programs can then be sent to a cypress development board. It can be compiled under Linux.

这是用ansys/LSDYNA模拟的裂纹扩展的k文件，适用于LSDYNA求解(This is the K file using ansys/LSDYNA simulation of crack extension, suitable for solving LSDYNA)

51单片机的数字显示代码，开发板上的例程，大家看看。(51 Singlechip figures show the code, development board routines, take a look at everyone.)

STM32与串口屏通讯，实现简单的交互功能，可作为基础参考程序(STM32 communicates with serial screen, realizes simple interaction function, and can be used as basic reference program.)

说明：  AD7799 AD转换芯片，电压采集驱动程序。(AD7799 AD conversion chip, voltage acquisition driver.)

我使用的是F103VET6，软件IIC控制，改引脚配置后可方便移植。 SDL连接PB6、SDA连接PB7、CS连接高电平，SDO连接高电平的话模块的写地址为0x3A、读地址为0x3B··· ···(I use F103VET6, software IIC control, pin configuration can be easily transplanted. SDL connects PB6, SDA connects PB7, CS connects high level. SDO connects high level telephone module with write address of 0x3A and read address of 0x3B.)

说明：  步进电机的电子详细资料、对于了解步进电机3(For more information on the electronic stepper motor, stepper motor for about 3)

GSM的原理图，是通过实验的原理图，绝对没有问题，欢迎下载。谢谢(GSM schematics, experimental schematic is absolutely no problem, welcome to download. Thank you)