cec13Benchmarks_matlab

stm32 mini板dht11温湿度测试程序(stm32 mini board dht11 temperature and humidity testing procedures)

atmeg8 ds1307 RTC实时时钟芯片操作。。(atmeg8 ds1307 RTC)

基于ARM的俄罗斯方块设计，本次将设计实现一个用C语言编写的、在基于ARM核心的ADuC7020 ARM开发板上实现的单机版的俄罗斯方块小游戏。使用Keil3编程软件对C语言代码进行编写，支持按键操作，在实现过程中涉及了LCD液晶屏的图形显示、按键控制、LED控制、中断、蜂鸣器等嵌入式的编程技术。(Tetris ARM-based design, this will be designed to achieve a C language, the ADuC7020 ARM development board ARM core-based implementations of stand-alone version of the Tetris game. Use Keil3 programming software code written in the C language, support for key operations involved in the implementation process of the LCD screen graphical display, control buttons, LED control, interrupt, buzzer embedded programming techniques.)

用stm32单片机进行pwm输出和ADC设置(USE STM32 MCU OUT PUT PWM WAVE AND ADC)

汽车华容道，实现汽车华容道各种布局的路径的解法。(Car Huarong, Huarong realize various automotive solution path layout.)

说明：  仿真机床切割,可生产可编辑的轨迹代码,方便操作.(Simulated machine tool cutting, can produce editable trajectory code, easy to operate.)

4维简单胞映射程序: 对动力系统做全局分析(four-dimensional simple cell mapping procedures : dynamic systems analysis of the overall situation so)

滤波器广泛应用于数字信号处理、通信、自动控制领域,但设计可变宽频带有源滤波器则比较困难。利用单片机控制参数可编程的双二阶通用开关电容有源滤波器,精确设置有源滤波器的中心频率f，品质因数Q及有源滤波器的工作方式。本系统主要分为两个部分:即程控滤波器和程控放大器。程控放大器电压增益为40dB，通过单片机控制DA进行分压，可精确实现要求的10dB步进，误差小于0.5 ，通带为100Hz-500KHz，输入电压峰－峰值范围为10mV，在输入范围内无明显失真。由MAX264为核心的滤波器，可设置为高通、低通滤波器。通过单片机直接给出控制频率，使-3dB截止频率在1KHz-20KHz内可调，步进1KHz，误差小于1 。整个系统以52单片机为控制核心，电路简单，性能稳定，且具有较高精度，滤波参数调节通过单片机控制，较为方便。(Filters are widely used in digital signal processing, communications, automatic control area, but the design variable wideband active filter is more difficult. Control parameters using single-chip programmable universal switched-capacitor biquad active filter, active filter accurately set the center frequency f, quality factor Q and the active filter works. The system is mainly divided into two parts: the program-controlled filters and programmable amplifiers. Programmable amplifier voltage gain of 40dB, the DA through the partial pressure of single-chip control, can accurately achieve the required 10dB step, the error is less than 0.5 , passband to 100Hz-500KHz, input voltage peak- the range of 10mV, the input range no significant distortion. By the MAX264 as the core of filter can be set to high pass, low pass filter. Given directly by the microcontroller controls the frequency, the-3dB cutoff frequency at 1KHz-20KHz adjustable, step 1KHz, error is less than 1 . The entire system for)

基于msp430f2618的lcd的液晶图形显示程序(Based on msp430f2618 the lcd LCD graphics display program)

GT400运动控制系统上位机轮廓插补控制程序(GT400 motion control system host computer contour interpolation control procedures)