程序 (1)

Matlab源程序，用于反射率积分计算，加权平均反射率的计算。(Matlab source for reflectivity of integral calculation, the calculation of the weighted average reflectivity.)

传统的短时谱估计语音增强算法通常假设语音谱分量相互独立，没有考虑语音谱分量间的相关性。针对这 一问题，该文提出一种新的基于多元Laplace分布模型的短时谱估计算法。首先，假设语音的离散余弦变换(DCT) 系数服从多元Laplace分布，以此利用谱分量间的相关性；在此基础上，利用多元随机矢量的高斯尺度混合模型表 示，推导得到语音DCT系数矢量的最小均方误差(MMSE)估计的解析表达式；并进一步推导了基于该分布模型的 语音存在概率，对最小均方误差估计子进行修正。实验结果表明，该算法在抑制背景噪声和减少语音失真等方面优 于传统的语音增强方法。(The spectral components of speech are usually assumed to be independent in traditional short-time spectrum estimation, which is not the case in practice. Tosolve this problem, a new speech enhancement algorithm with multivariate Laplace speech model is proposed in this paper. Firstly, the speech Discrete Cosine Transform (DCT) coefficients are modeled by a multivariate Laplace distribution, so the correlations between speech spectral components can be exploited. And then a Minimum-Mean-Square-Error (MMSE) estimator based on the proposed model is derived using a Gaussian scale mixture representation of random vectors. Furthermore, the speech presence uncertainty with the new model is derived to modify the MMSE estimator. Experimental results show that the developed method has better noise suppression performance and lower speech distortion compared to the traditional speech enhancement method. )

软件无线电通信系统matlab仿真，同时内有所有备注(Software radio communication system matlab simulation, at the same time with all notes)

1． 该光盘包含了“信号与系统分析及MATLAB实现”一书的第九章所有程序； 2． 为了方便读者阅读程序，所有程序均采用中文注释。MATLAB的程序编辑器不支持中文显示，用户只需在Word下直接打开源程序文件，即可阅读程序中的中文注释； 3． 程序文件的命名分为以下三种类型： （1） 若为书中例题的程序，则程序文件名一律以ex开头，后面跟4位数字（前两位表示章号，后两位表示例题序号）表示的该程序所在例题的编号。例如，ex0603.m是例6.3的程序，而ex1102.m则是例11.2的对应程序。 （2） 若为书中图形的实现程序，则程序文件名一律以figure开头，后面跟4位数字（前两位表示章号，后两位表示图形序号）表示的该程序所绘图形的编号。例如，figure1203.m是实现图12.3的程序，而figure0710.m则是实现图7.10的对应程序。 （3） 若为函数文件，则直接以函数名命名，例如文件sconv.m即是书中函数sconv()的对应程序。 ()

遗传算法对PID参数寻优实现倒立摆控制。(these programms fulfil the GA methods to find the global optima of the control parameters for a pid controller of an inverted pendulum.)

智能控制编程及其在matlab中如何应用实现(Intelligent control programming and its implementation in matlab how to apply)

matlab调用c程序经典实例,详细注释了接口函数和参数的意义功能，并以实例的形式完成matlab对c程序的调用(a classic example of matlab calling C source codes)

光纤耦合仿真MATLAB程序包，可以仿真不同芯径的光纤模式分布，可以仿真光纤的耦合损耗。(fiber coupling simulation)

根据直扩原理，首先有随机数发生器产生一系列二进制信息数据（+1，-1），每个信息比特重复Lc次，Lc对应每个信息比特所包含的伪码片数，包含每一比特Lc次重复的序列与另一个随机数发生器产生的PN序列c(n)相乘。然后在该序列上叠加高斯白噪声和形式为i(n)=Acosw0n余弦干扰下次信号，切余弦干扰信号的振幅满足条件A<Lc。在解调器中进行与PN序列的互相关运算，并且将组成各信息比特的Lc个样本进行求和。加法器的输出送到判决器，将信号与门限值0进行比较，确定传送的数据为+1还是-1，计数器用来记录判决器的错判数目。(According to the principle, first some straight expansion random number generator produces a series of binary data (+ 1-1), each information bit repetitive Lc times, Lc for each information bit contains PN code piece count, embraces each bit Lc times repeated sequence and another random number generator produces PN sequence c (n) multiplication. Then in the sequence superimposed on gaussian white noise and forms as I (n) = Acosw0n cosine interference next time signal, cut cosine interfering signal amplitude satisfy conditions A < Lc. In the modem with the cross-correlation operation PN sequence, and the information will comprise the Lc a sample bits peace. The output of the adder judgment device, will signal to compare with threshold 0 data transmitted, determine for+ 1 or-1, counter is used to record the number victimised judgment. )

东北大学关于通信信号处理的matlab课件，适合初学者理解学习(Northeastern University, on the communication signal processing matlab courseware, suitable for beginners to learn to understand)