xinhaofashengqi

利用单片机实现快速傅里叶变换 基于单片机对数据的采集(Fast Fourier transform using MCU Microcontroller based data acquisition)

单片机调试实现信号发生器功能的C源代码，包括三角函数、方波等等(Single-chip debugging functions for signal generator of C source code, including trigonometric, square, etc.)

一个用C语言控制的读写7022，存储数据，485上传数据，向液晶模块显示数据的程序。此程序为测试程序，所有与模块通讯功能都能实现。(A use of C language to read and write control 7022, data storage, 485 From the data, display data to the LCD module procedures. This procedure for testing procedure, all communication functions and modules can achieve.)

旋转LED的实现,实现用单片机控制电机转速，采用无线供电方式哦(Rotate the LED, achieving MCU control motor speed, the use of wireless power supply oh)

同三维万能采集卡系列开发SDK包,包含例程等! (With three-dimensional universal capture card series development SDK package includes routines, etc.!)

此程序为利用Kinect v2实现用手指隔空控制鼠标,效果非常好。 运行环境 Kinect for Windows V2 Kinect SDK 2.0 OpenCV 3.0(This program is implemented with the use of Kinect v2 finger Taking control the mouse, the effect is very good. Operating environment Kinect for Windows V2 Kinect SDK 2.0 OpenCV 3.0)

单片机驱动数模转换器ADC0809的接口程序员(Single-chip driver DAC ADC0809 interface programmers)

基于stm32fl03系列的Nokia5110液晶屏的驱动，使用方便简单 有英文字符串和汉字显示两种功能(Based Nokia5110 LCD driver stm32fl03 series, easy to use simple English strings and character display two functions)

基于M0516的魔球灯控制程序，内含原理图，功能有内置PWM加模拟PWM线性调光，炫耀的自走程序与声控程序，主从控制模式，IIC协议，485通讯DMX512协议，74HC595控制四位3461共阴数码管，ULN2803电机驱动程序(M0516 based magic ball lamp control procedures, the enclosed schematic diagram, function has a built-in PWM analog PWM linear dimming, showing off the go program with voice control, master-slave control mode, the IIC agreement, 485 communication DMX512 protocol, 74 hc595 are needed to control the four digital tube, 3461, a total of Yin ULN2803 motor drivers)

说明：  单片机MC9S08AW60脉宽调制 TPM1CH3 LS2亮度控制 KBI SEG控制亮度等级 。本工程为定时器输出PWM波测试工程实例通过对PWM占空比的调节,实现小灯的渐亮的功能,当占空比为100％时再从0％逐渐增加.PWM的周期一定要足够的快,否则其输出电压的波动范围很大,且测不出一个稳定的电压值,这样通过就观察不到小灯渐亮效果. 另外,在改变PWM的周期和占空比之前和之后要分别禁止和使用。(MC9S08AW60 pulse width modulation TPM1CH3 LS2 brightness control KBI SEG brightness level. This project is an example of testing the output PWM wave of the timer. By adjusting the duty ratio of the PWM, the function of the small lamp gradually brightening is realized. When the duty ratio is 100%, the period of the small lamp gradually increases from 0%. The period of the PWM must be fast enough. Otherwise, the fluctuation range of the output voltage is large and a stable voltage value can not be measured, so the effect of the gradual brightening of the small lamp can not be observed. In addition, the period of the PWM is changed. Before and after duty cycle should be prohibited and used separately.)