用于labview excel写入程序

火车故障检测系统 很好的初学者学习程序 主要有关数据采集(Train fault detection system good for beginners to learn about the main data acquisition program)

基于LabvIEw的通用自动测试系统(ATs)舍计算机，可鳊程激励、响应数据采集及uuT模块，采用MxI总线控制方式。专用信号发生器为uuT提供模拟激励信号，矩阵开关和适配器完成不同信号间切换。主控计算机执行测试程序，信号发生器发送激励信号，数据采集卡采集数据，采集数据经调理后，并与标准数据|匕较是否满足相应测试结果。(The general automatic test system (ATs) based on LabvIEw can be used as a computer to excite, respond to data acquisition and uuT module. The control mode of MxI bus is adopted. Special signal generator provides analog excitation signal for uuT, matrix switch and adapter complete switching between different signals. The main control computer executes the test program, the signal generator sends the excitation signal, the data acquisition card collects the data, after the data acquisition is adjusted, and compares with the standard data | dagger whether it meets the corresponding test results.)

主要运用labview的编程功能完成对信号的功率谱分析，从而更好的理解功率谱。(The main use labview programming features to complete the signal power spectrum analysis to better understand the power spectrum.)

解决LabVIEW里不能使用数码管字体的方法 用FontCreator软件打开字体，将字体的平台由“Windows Unicode BMP(UCS-2)”改为“Windows Symbol”即可。(Method for solving LabVIEW can not use digital tube font With FontCreator software to open the font, the font platform Unicode BMP Windows (UCS-2) to Symbol Windows can be.)

使用LabVIEW将其他建模软件的3D模型导入到LabVIEW中。(3D models using LabVIEW to other modeling software into LabVIEW.)

使用Labview编写PC端USB通讯程序，与C8051f320进行大规模数组USB通讯。文件中Device部分是Silab提供的FileTransfer例程，适用于C8051f320；Host部分中VC程序Silab提供的原例程，Labview程序是根据VC程序自主改写移植而成。已通过测试验证。(Interface for USB communicatons on PC, was coded by Labview, and it can transfer(USB) big array with C8051f320. The Device folder from Silab s example "FileTransfer", and the VC code in Host folder also. The VI in Host folder is code basic the VC code. The VI passed test.)

labview 计算 CRC ，通过labview 计算CRC 校验(labview COUNT CRC 32BIT LABVIEW)

说明：  利用labview常用架构JKI SMO简单设计一款测试系统(A simple test system is designed by using the common architecture jki SMO of LabVIEW)

labview与西门子plc通讯工具，读取plc内的数据，修改plc内部寄存器值，PLC交互(LabVIEW and Siemens PLC communication tools, read the PLC data, modify the PLC internal register value, PLC interaction)

说明：  使用labview采集16通道数据，采集10次，保存成tdms格式，并对所有数据进行频谱分析，有效值和峭度等指标的10次趋势分析，可在趋势图中点击光标查看原始波形(Using LabVIEW to collect 16-channel data, collect 10 times, save them in TDMS format, and analyze 10 times trend of all data, such as spectrum analysis, RMS and kurtosis. Click on cursor in trend map to see the original waveform.)