PMAC 中文手册（推荐详细）

说明：  利用定时/计数器T0从P1.0输出周期为1s的方波，让发光二极管以1HZ闪烁，设晶振频率为12MHz(The use of timer/counter T0 from P1.0 output cycle square wave 1s, so that the light-emitting diodes 1HZ blinking, set the crystal frequency is 12MHz)

英飞凌单片机使用pec中断的ad转换实例完整版(Infineon microcontroller interrupt the ad conversion using pec)

激光切割上位机源码，生成NC刀路，不含NC扩展插件。(Laser cutting the host computer source code, generate NC knife road)

说明：  This is a generic FIFO buffer that can be used to store any kind of items. It is written in C language and can be compiled and used on almost any architecture. It was designed to be used on memory limited architectures such as microcontrollers. Examples of the applications that can be built with this library include:

智能交通单路口C++仿真程序，其中设置了随机车辆产生，以及信号配时功能，程序编译已验证(Intelligent Transportation single intersection C++ simulation program, which is set to generate random vehicles, as well as signal timing functions, the program compiled Verified)

针对RN8209新型电表计量芯片的校表软件，使用DLT645-2007通讯协议(RN8209 for new electricity metering chip calibration software, communications protocols using DLT645-2007)

Springer - WI-FI, BLUETOOTH, ZIGBEE AND WIMAX Wi-FiTM: Architecture and Functions (Springer- WI-FI, BLUETOOTH, ZIGBEE AND WIMAX Wi-FiTM: Architecture and Functions)

由于太阳能充电系统多在户外，为了方便研究太阳能充电控制系统对蓄电池的充电情况，本文使用GPRS无线传输技术，设计了一套太阳能充电系统蓄电池的充电电压电流远程实时监测系统。系统的硬件部分由电压电流检测电路、单片机STC89C52RC、GPRS模块SIM300以及相应的外围电路构成，下位机软件由C语言编写并与硬件部分构成系统下位机部份，实现了对充电电压电流的信息采集以及数据的无线数传。上位机在LabVIEW2010环境下编写，具备友好的人机交互界面，实现了数据的远程接收、实时显示、数据库管理、报表生成和打印等功能。经过系统测试系统实现了对电压电流的远程监测。(As the solar charging system more outdoors, in order to facilitate the study of solar charge control system for charging the battery case, we use GPRS wireless transmission technology, we designed a solar charging system battery charge voltage and current remote monitoring system. The hardware part of the system by the voltage and current detecting circuit, microcontroller STC89C52RC, GPRS module SIM300 and corresponding peripheral circuits, lower computer software written in C language and hardware parts lower position machine part of the system, the realization of the charging voltage and current information collection and wireless data transmission of data. PC at LabVIEW2010 prepared environment, with friendly interactive interface, realize the remote receiving data, real-time display, management, report generation and printing. After the system test system enables remote monitoring of voltage and current.)

Energy efficiency is the most important design goal for wireless sensor networks (WSNs). In this paper, we propose an energy-efficient cooperative MIMO scheme, which combines energy-efficient LEACH (EE-LEACH) protocol and cooperative MIMO. We name it as EE-LEACH-MIMO scheme. EE-LEACH is an improved LEACH algorithm, in which the network is partitioned to sectors with equal angle for avoiding the distribution non-uniformity of cluster heads. In EE-LEACH-MIMO scheme, the location and the residual energy of each node are considered when the cluster heads for clustering and cooperative nodes for MIMO system are chosen. For comparisons, LEACH, EE-LEACH, the simple cooperative scheme with LEACH and MIMO (LEACHMIMO), and EE-LEACH-MIMO scheme are simulated. The result shows that EE-LEACH-MIMO scheme can well balance the network load, save energy and prolong the network lifetime

VB 开发C51的动态链接库，可以拿来直接用的，(VB-C51 dynamic link library that can be used directly, and)