OFDM-MATLAB-仿真程序

In this paper, an implementation and dynamic modeling of a three-phase induction motor using Matlab/Simulink are presented in a step-by-step manner. The model was tested by two different ratings of a small and large induction motors. The two simulated machines have given a satisfactory response in terms of the torque and speed characteristics.

FDTD方法，以PML为边界条件，是二维的算法(FDTD method, the PML boundary condition is two-dimensional algorithm)

一个很好的matlab图像处理资料，希望对大家有帮助(A good matlab image processing information, we want to help)

本设计主要对4PSK调制方式的信号，利用MATLAB的m文件进行最佳接收机的设计与仿真。对输入的叠加噪声的4PSK调制信号进行接收，利用相关解调器来实现信号解调，及最大似然准则来实现检测器。在相关解调器中，接收信号分别与基函数 和 相乘再积分。在检测器中，利用相位来判断输出，从而最终得到接收的数据。采用随机二进制数通过4PSK调制后叠加高斯白噪声再对设计的接收机进行测试，从测试的结果可看出，在信噪比大于-8dB时，误码率为0，说明该接收机较好的实现了抗噪声性能。(The design of the main 4PSK modulation mode of the signal, the use of MATLAB m file for the best receiver design and simulation. The 4PSK modulated signal of the input superimposed noise is received, and the demodulator is realized by the relevant demodulator, and the maximum likelihood criterion is used to realize the detector. In the associated demodulator, the received signal is multiplied by the basis function and multiplied by the basis function. In the detector, the output is judged by the phase, and finally the received data is obtained. Using the random binary number through 4PSK modulation after the superposition of white noise and then the design of the receiver to test the test results can be seen in the signal to noise ratio greater than-8dB, the bit error rate is 0, indicating that the receiver is better The realization of the anti-noise performance.)

病虫害分类用,用来进行病害虫分类的MATLAB程序(Pest and disease classification used, the classification used for pest MATLAB program)

BOC(1,1)的编码，BOC(1,1)的功率谱密度，可以完美运行，对做BOC编码的人很有用途(BOC (1,1) code, BOC (1,1) power spectral density, can run perfectly on the very people who make use of BOC coding)

LDPC的译码算法，其中使用matlab和C的联合编程，C主要做了译码算法，并且有性能的仿真测试(LDPC decoding algorithm, including joint programming matlab and C, C major to do the decoding algorithm and performance simulation test)

For example, heating up the temperature in a room is a process that has the specific, desired outcome to reach and maintain a defined temperature (e.g. 20°C), kept constant over time. Here, the temperature is the controlled variable. At the same time, it is the input variable since it is measured by a thermometer and used to decide whether to heat or not to heat. The desired temperature (20°C) is the setpoint. The state of the heater (e.g. the setting of the valve allowing hot water to flow through it) is called the manipulated variable since it is subject to control action

turbo code simulation in matlab

实现数字音频信号的幅频均衡，采用了lms算法和rls算法，有MATLAB的simulink模型，和m文件，还有部分c程序，已经本人完全测试过。(Digital audio signal of the amplitude-frequency equalization, using lms algorithm and rls algorithms, there are MATLAB-simulink model, and the m file, as well as part of the c program, I have been completely tested.)