gie-fx30

fuzzy control rule design

关于MATLAB开发dsp的一个例子,比较方便使用，作为指导拓展用(an example for developing dsp using matlab )

直线阵采用切比学夫加权控制主旁瓣比，抑制噪声。此程序基于常规波束形成实现，程序思路清晰，适合刚接触阵列信号处理的人参考。(Linear array by cutting the right of control over the primary school laid upon the side-lobe ratio, noise suppression. This program is based on conventional beamforming implementation process with clear ideas for people new to reference array signal processing.)

说明：  详细研究了单级倒立摆起摆控制方法，并给出了详细的仿真模型与仿真效果(Detailed study of the single inverted pendulum swing-up control method, and gives a detailed simulation model and simulation results)

说明：  多能源系统优化包含粒子群SVM等优化算法，提供模糊数据以及仿真结果，仅供参考哦(Multi energy system optimization includes particle swarm SVM and other optimization algorithms, providing fuzzy data and simulation results for reference only)

滑模变结构控制仿真实例，为基础的滑模变结构入门程序，建议初学者参考使用(Sliding mode variable structure control simulation example, based on sliding mode variable structure entry procedures, the proposed reference to the use of beginners)

Analysis of Induction motor

matlab 安装过程指南介绍 英文版 (matlab installation guide explains in English)

The function translates from labels of a binary tree to corresponding rows (R) and columns (C) of a 2 dimensional matrix storing the tree according to predefined convention, given below. The storing matrix preserves the fractal-like topology of the tree.

基于MATLAB利用Particle-in-cell模型,对梯形管内壁等离子体离子注入过程,进行了二维数值模拟.计算结果表明在中心电极附近出现了“阳极鞘层”,该鞘层内部不存在离子,而且在鞘层边缘离子密度最高.在上下管壁上的离子注入剂量呈现“m”形分布.通过对注入过程中等离子体密度分布和不同时间段管壁不同位置离子注入剂量的跟踪,发现“阳极鞘层”扩展行为是导致“m”形分布的原因.由于梯形管形状的不对称性,“阳极鞘层”的边缘向梯形长底方向扩展较快.在注入初始时刻离子注入的能量很低,随着时间延长离子能量逐渐升高,这是由离子初始位置决定的.可见梯形管自身形状决定了鞘层形状和最终的离子注入能量和剂量分布.(Based on MATLAB use Particle-in-cell model, the trapezoidal pipe wall plasma ion implantation process, the numerical simulation of two-dimensional calculation results show that in the vicinity of the center electrode to a "anode sheath," which does not exist inside the plasma sheath, and the highest in the sheath edge ion density ion implantation dose showing the upper and lower walls of the "m"-shaped distribution through the process of injecting the plasma density distribution and the wall at different locations in different time periods ion implantation dose tracking, found that "anode sheath "extension behavior is leading to" m "-shaped distribution of the reasons due to the asymmetry of the trapezoidal shape of the tube," Edge anode sheath "extension to the end of a long trapezoid direction quickly in the initial moment of implantation energy ion implantation is low ion energy with time gradually increased, which is determined by the initial position of the ion. visible trapezoida)