qwybdpzf

此时例是关于用matlab实现牛顿法求解非线性方程组，（包含牛顿法、改进的牛顿法.梯度法、最速下降法代码），里面附带可以直接运行的程序。(At this case is about solving nonlinear equations using matlab Newton, (including Newton, Newton method to improve the code), which comes with the program can be run directly.)

有关稀疏离散分数阶傅里叶的程序，其中有稀疏脉冲压缩的事例(Procedures for sparse discrete fractional Fourier, which has sparse pulse compression stories)

这个程序使用了遗传算法来优化点对点之间的轨迹度量。(This code proposes genetic algorithm (GA) to optimize the point-to-point trajectory planning for a 3-link (redundant) robot arm.)

实现通信抗干扰的跳频通信，希望对初学通信抗干扰的同志有所帮助(To achieve interference rejection for frequency hopping communication, hope to comrades beginner help communication interference)

以DUFFING方程为例，此程序运行了非线性方程的分岔图。(take DUFFING equation, for example, the program run the nonlinear equation of bifurcation diagrams. )

peec电路电感和互感计算的解析公式，精确解，适用于peec等效电路，分布式电网络(Peec circuit inductance and mutual inductance calculation of analytical formulas, the exact solution, apply to the peec equivalent circuit, a distributed electric network )

此函数介绍了非线性函数在MATLAB理是通过什么函数进行拟合的(This function describes the nonlinear function in the MATLAB function through what management is fitting)

说明：  本目录主要包括：文档和两个源代码。 其中一个源代码是识别程序的，另一个是一个矩阵类库的，书里面也使用过，所以一并附上。 因为已经保存了训练好的网络权值，所以第一次使用识别程序时，可以直接运行\\Release目录下的可执行文件，然后对图片目录中的测试图片进行读入、识别。 当然读者也可以自行用训练样本训练网络，不过要特别注意训练样本的选择，否则可能造成识别率很低。训练样本选择的原则是，尽可能的有代表性，在训练时间不至于太长的情况下，训练样本数目尽量多。 ( This directory includes: documentation and two source code. One of the source code is to identify the procedure, the other is a matrix class library, the book which is also used, so be attached. Because it has saved the trained network weights, so the first use of identification procedures, you can directly run \ \ Release directory of the executable files, and then tested on the images directory to read pictures, identification. Of course, readers are free to use the training samples to train the network, but pay special attention to training samples, otherwise it may cause very low recognition rate. Training sample selection principle is that as far as possible, representative, in the long training time Buzhi Yu s case, the number of training samples as much as possible. )

有两个代码文件，是分别计算微带贴片天线设计时背馈和侧馈两种情况下的天线尺寸的，很全很精确！(There are two code files, which separately calculate design of microstrip patch antenna fed back and the side-fed both cases, the antenna size, it is all very precise!)

WCDMA物理层matlab仿真程序，包含信道编码，交织，速率匹配，调制，扩频，信道模型，RACK接收机和相应的解码程序。(A simulation of the 3GPP FDD proposal for 3G wireless. The simulation can run on Simulink or as a stand alone C-coded program. It includes the channel encoding, interleaving, rate matching, modulation, spreading(channelization), a channel model, a RAKE receiver, and the corresponding decoding functions. Both the downlink and uplink have been modelled.)