banggun_V4.6

维也纳科技大学的关于LTE的系统级仿真平台，可以作为初学者使用。(Vienna university of science and technology, the system about LTE level simulation platform, can be used as a beginner)

it s important thing for development

5 link simulation technique using matlab

永磁同步电机系统的滑模观测器设计，非常实用，算法很先进(Sliding model observer based Permanent Magnet Synchronous Motor)

this file can help you on equalizing your network datas.

说明：  matlab 经典算法的程序，包含插值，规划，数据分析等(classical algorithm matlab procedures, including interpolation, planning, data analysis, etc.)

Designs a linear phase FIR lowpass filter such that it: - minimizes the filter order - has a constraint on the maximum passband ripple - has a constraint on the maximum stopband attenuation (This is a quasiconvex problem and can be solved using a bisection. minimize filter order n s.t. 1/delta <= H(w) <= delta for w in the passband |H(w)| <= atten_level for w in the stopband where H is the frequency response function and variable is the filter impulse response h (and its order/length). Data is delta (max passband ripple) and atten_level (max stopband attenuation level). )

《深入浅出数字信号处理》这本书中的源程序，matlab语言编写。(The " layman digital signal processing" book source)

本演示实现了主动轮廓模型由Kass等人提出。 要运行它的图形用户界面 1。基于MATLAB型引导提示。 2。关于“到现有的图形用户界面，点击” 3。选择在与本文件相同的目录snk.fig文件 4。按一下上方的绿色箭头启动图形界面 一旦GUI已经启动，您可以通过使用蛇 1。点击“新形象”，并加载输入图像。提供的样品图像。 2。平滑参数设置“西格玛”或保留其默认值并点击“过滤器”。这将平滑图像。 3。只要你点击“过滤器”，头发会出现交叉，用他们和你左击鼠标，您可以选择在图像上的初始轮廓的位置。会出现一个红色圆圈到处您单击并在多数情况下，你应该单击对象周围的一切你想要的部分。最后一点，必须挑选使用右键单击，以阻止更多的积分为MATLAB的要求。 4。设置各种蛇参数（在能源方面的相对权重的蛇目标函数）或离开它们的默认值，然后按一下他们“迭代”按钮。蛇会出现和移动，因为它收敛到它的低能量状态。(This demo implements the Active Contour Models as proposed by Kass et al. To run it with GUI 1. Type guide on the matlab prompt. 2. Click on "Go to Existing GUI" 3. Select the snk.fig file in the same directory as this file 4. Click the green arrow at the top to launch the GUI Once the GUI has been launched, you can use snakes by 1. Click on "New Image" and load an input image. Samples image are provided. 2. Set the smoothing parameter "sigma" or leave it at its default value and click "Filter". This will smooth the image. 3. As soon as you click "Filter", cross hairs would appear and using them and left click of you mouse you can pick initial contour location on the image. A red circle would appear everywhere you click and in most cases you should click all the way around the object you want to segment. The last point must be picked using a right-click in order to stop matlab for asking for more points. 4. Set the various snake paramete)

用Maple和MATLAB解决科学计算问题(Using Maple and MATLAB scientific computing to solve problem)