18b20

SIM900开发板配套STM32 GPRS代码(SIM900 STM32 GPRS driver)

绿灯亮时，准许车辆通行，黄灯闪烁时，已越过停止线的车辆可以继续通行；没有通过的应该减速慢行到停车线前停止并等待，红灯亮时，禁止车辆通行。给行人看的叫人行横道灯，通常指由红、绿（绿为蓝绿）二种颜色灯组成用来指挥交通通行的信号灯，红灯停，绿灯行。(When the green light is on, the vehicle is allowed to pass. When the yellow light is flashing, the vehicles that have crossed the stop line can continue to pass.You should slow down to stop and wait at the stop line. No traffic is allowed when the red light is on.Pedestrian crossing lights for pedestrians, usually denoted by red, green (green, blue, green), two color lamps used to direct traffic signals, stop at red lights and green.)

敦泰科技触摸IC源码，非常好的C语言学习源码程序，(Touch IC source, Thai science and technology, a very good C language source code program,)

根据对应的按键值，对应输出相应的电容值，并做掉电检测(According to the corresponding key value, corresponding to the output of the corresponding capacitance values ​ ​ and do brownout detection)

单片机为at89s52控制步进电机正反调速实验,(The stepper motor positive and negative control experimental)

本方案是基于富士通高可靠性单片机开发的锂电池电动螺丝刀，采用直流无刷电机作为核心，配合方波驱动以及闭环控制技术，实现电动工具的可靠运行。 技术参数 1）采用日本富士通MCU，性能稳定，抗干扰强，高可靠性； 2）直流18V输入（可兼容不同锂电池10V—36V）； 3）三相霍尔直流无刷电机驱动，转速高达25000转/分； 4）采用德国英飞凌高性能MOS/IGBT，驱动功率高达800W； 5）高亮LED照明，工作时点亮，不工作时自动熄灭； 6）采用智能控制技术实现待机（不工作时）功耗为 0 消耗； 7）通过软件实现软启动，启动时间可调整，瞬间（1S）达最高速； 8）具有过流保护、堵转保护、过压欠压保护； 9）带速度设置按键、正反转按键、调速开关； (The program is based on the Fujitsu MCU development of high reliability lithium battery electric screwdriver, brushless DC motor as the core, with the square wave drive and closed-loop control technology, power tools for reliable operation.)

以c51单片机为核心，利用1760芯片进行语音报时，51单片机控制(With c51 microcontroller core, the use of 1760 chip for voice timekeeping, 51 MCU control)

红外遥控解码，基于51单片机的例程，简单实用，我在学习单片机的时候用到的(Infrared remote control decoding, based on 51 MCU routine, simple and practical, I used the time to learn microcontroller)

1单片机 控制直流电机转速 PID算法+C语言程序+Proteus仿真 采用PID控制算法控制电机转速，使得电机实际转速与设定转速保持一致。(1 MCU control DC motor speed PID algorithm+C language program+Proteus simulation using PID control algorithm to control motor speed, so that the actual motor speed and the set speed consistent.)

飞思卡尔单片机锁相环程序，详细说明了锁相环的配置步骤以及计算方法(Freescale MCU PLL procedures, a detailed description of the PLL configuration steps and calculation methods)