haisanids

课程设计自己编写的一个网络抓包软件，MFC界面，并且对包进行分析。很值得学习哦。(Design their own curriculum prepared by a network of ethereal, MFC interface, and the right package for analysis. Oh, very much worth learning.)

程序可以获取本机IP地址，需要先加载Socket库(Program can access the machine IP address, need to load the Socket Library)

客户端连接服务器的程序，以此测试客户端是否连接上。(client programming source)

Implementing push-to talk with hotkey operation(Implementing a push- to talk with hotkey operation)

Visual C++案例开发集锦第六章\聊天室服务器端开发的程序源码,值得一看！(Visual C++ case development highlights Chapter Chat server-side development of the program source code, worth a visit!)

socket编程实现服务端与客户端互发消息(exchange message between server and client)

基于CSocket点对点文件传输，用c++实现。(CSocket file transfer developed by c++)

UDP方式双网冗余程序，一网卡断开，另一网卡自动连接，从而保证通讯正常(UDP mode dual-network redundancy procedures, disconnect a network card, another card to connect automatically to ensure the normal communication)

中频感应加热以其加热效率高、速度快，可控性好及易于实现机械化、自动化等优点，已在熔炼、铸造、弯管、热锻、焊接和表面热处理等行业得到广泛的应用。 本设计根据设计任务进行了方案设计，设计了相应的硬件电路，研制了20KW中频感应加热电源。 本设计中感应加热电源采用IGBT作为开关器件，可工作在10 Hz～10 kHz频段。它由整流器、滤波器、和逆变器组成。整流器采用不可控三相全桥式整流电路。滤波器采用两个电解电容和一个电感组成Ⅱ型滤波器滤波和无源功率因数校正。逆变器主要由PWM控制器SG3525A控制四个IGBT的开通和关断，实现DC-AC的转换。 设计中采用的芯片主要是PWM控制器SG3525A和光耦合驱动电路HCPL-316J。设计过程中程充分利用了SG3525A的控制性能，具有宽的可调工作频率，死区时间可调，具有输入欠电压锁定功能和双路输出电流。由于HCPL-316J具有快的开关速度（500ns），光隔离，故障状态反馈，可配置自动复位、自动关闭等功能，所以选择其作为IGBT的驱动。 对原理样机的调试结果表明，所完成的设计实现了设计任务规定的基本功能。此外，为了满足不同器件对功率需要的要求，设计了功率可调。这部分超出了设计任务书规定的任务。(induction heating with high heating efficiency, speed and good controllability and easy to mechanization. the advantages of automation, in melting, casting, bending, forging, welding and surface heat treatment and other industries have been widely employed. According to the design tasks for the design of the program design, design corresponding to the hardware circuit, Development of 20 KW induction heating power. The design of induction heating power IGBT used as a switching device, which can work in 10 Hz- 10 kHz frequency band. It consists of rectifier, filter, and the inverter components. Controlled Rectifier not use the entire three-phase bridge rectifier circuit. 2 filter used an electrolytic capacitor and inductor components II-type filter and passive PFC. Inverter mainly by the PW)

编写程序，实现基于ARP协议获取本局域网内全部活动主机MAC地址与IP地址对应关系列表，要求使用Winpcap，手动封装ARP数据包，并实现ARP响应数据包的接收和解析。(programming, ARP-based LAN access to the activities of all MAC address and IP address correspondence list, require the use of Winpcap, manual Packaging ARP packets, and achieve ARP response data packet reception and analysis.)