110kv

99秒马表，在Proteus设计两个数码管动态显示及一个键盘SP。在ucos下结合keil完成开始时，显示“00”，第1次按下SP后就开始计时。 第2次按SP后，计时停止。第3次按SP后，计时归零。 (99 seconds stopwatch, two in the Proteus design dynamic digital tube display and a keyboard SP. Keil in combination ucos completed under the beginning of the show " 00" , 1st timer after pressing the SP. 2nd by SP, the time to stop. The 3rd by the SP, the time zero.)

说明：  本课题对基于单片机的交通灯控制系统进行设计。以MCS-51系列单片机为控制核心，设计并制作交通灯控制系统，用于十字路口的车辆及行人的交通管理。东西南北四个路口具有左拐、右拐、直行及行人4种通行指示灯，并分别用计时器显示路口通行转换剩余时间，在特种车辆如119、120通过路口时，系统可自动转为特种车辆放行，其他车辆禁止通行状态。(Traffic light control system based on SCM (Single Chip Microcomputer) is designed in this paper. System requires that MCS-51 series SCM is used as CPU. Traffic light control system should be designed and made .There are four groups light which indicate to turn left, turn right, and go straight ahead and pedestrian access in east, west, north and south four directions. Timer shows traffic conversion remainder time. When special vehicles, such as 119,120 go through, the system can automatically allow special vehicles running and other vehicles is prohibited.)

自动交通控制系统用红、绿、黄三支共两组发光二极管表示交通信号灯，利用单片机模拟有时间显示的定时交通信号灯控制管理。信号灯的变化规律可如下： 1）放行线：绿灯亮放行25秒，黄灯亮警告5秒，然后红灯亮禁止。 2）禁示线：红灯亮禁止30秒，然后绿灯亮放行。 3）当某一方向的红灯亮时，若该方向有车通过，则用扬声器声报警。（撞红灯信号可用3-5V模拟量表示）(Automatic traffic control system using red, green, yellow light-emitting diodes, said a total of three traffic lights, the use of single-chip analog time display on a regular traffic signal control and management. Changes of lights to be as follows: 1) Release Line: green clearance 25 seconds, the yellow light warning for 5 seconds, then the red light is prohibited. 2) ban shows lines: the red light is prohibited for 30 seconds, then the green light to release. 3) When the red light in one direction, if the direction of the car through, the alarm speaker sound. (Hit the red signal available 3-5V analog representation))

自行车的里程表。基于51单片单片机最小系统开发的(The bike' s odometer. Developed based on 51 single-chip microcontroller minimum system)

说明：  HT32F1755单片机基础程序,LCD,延时，定时器等等(HT32F1755 microcontroller-based program, LCD, delay, timers, etc.)

感应电动机的启动小程序，可以模拟启动过程，自动计算启动的参数，帮助初学者理解感应电动机的结构(Induction motor start-up small program that can simulate the boot process, automatically calculates the start parameters and Help beginners understand the structure of induction motor.)

显示器功能 加快程序开发初学者的进步脚步。让他们了解简单的显示程序的写法(Monitor function to accelerate the pace of progress in program development for beginners. So that they understand the simple display program wording)

超声波测距，测量精度为1cm，可以使机器人安全避障。(Ultrasonic distance measurement accuracy of 1cm, can make the robot obstacle avoidance safety.)

stm32，通过spi总线实现对于TI的2543AD进行读写操作，串口uart输出数据(stm32, achieved through the spi bus for read and write to TI s 2543AD, serial uart output data)

基于stm32单闭环pid调速控制，单电阻采样，正弦波驱动，pid调速。(Based on stm32 pmsm drive, single sampling resistor, sine wave drive, pid speed control.)