plot_PL_general

求peaks函数的极值。中间有一步需手动选取6个点。(get extream values of peaks function. You need to pick six points in one step.)

任务： 1） 借助MATLAB画出误差性能曲面和误差性能曲面的等值曲线（参考PPT2.1第17页的两幅图）； 2） 写出最陡下降法以及LMS算法的计算公式（取 ）； 3） 用MATLAB产生方差为0.05, 均值为0白噪音S(n)，并画出某次采样得到的波形（即产生任意一个噪声随机序列）； 4） 根据 2）中的公式，并利用 3）中产生的S(n)，在 1）中的误差性能曲面的等值曲线上叠加画出采用最陡下降法以及LMS法时H(n)的在叠代过程中的轨迹曲线（参考PPT2.1第17页的右下图的曲线1和曲线2）。 5）用MATLAB计算并画出LMS法时 随时间n的变化曲线（对应S(n)的某一次的一次实现）和e(n)波形； 注意：某一次实现的结果并不能从统计的角度反映实验的结果 的正确性，为得到具有统计特性的实验结果，可用足够多次的 实验结果的平均值作为实验的结果。用MATLAB计算并画出 采用LMS法时，J(n)的100次实验结果的平均值随时间n的变 化曲线（即 生成随机噪声信号并计算结果，重复执行100次， 求平均结果）。 6）在 1）中的误差性能曲面的等值曲线上，叠加画出采用LMS法得到的100次实验中的H(n)的平均值的轨迹曲线； (Task: 1 ) Draw with MATLAB error performance surface and surface contour error performance curve ( refer PPT2.1 two chart on page 17 ) 2 ) Write the steepest descent method and the LMS algorithm formula ( take ) 3 ) Using MATLAB to generate variance of 0.05 with a mean of 0 white noise S (n), and draw a particular sampling waveform ( ie, any noise generated random sequence ) 4 ) based on 2 ) of the formula , and use 3 ) generated in S (n), in a ) the error performance curves superimposed on the surface contour plot using the steepest descent method and the LMS method when H (n) the iterative process in the trajectory curve ( refer PPT2.1 page 17 bottom right of the curves 1 and 2 ) . 5 ) using MATLAB LMS method is used calculate and draw the curve with time n (corresponding to S (n) of a first implementation of a ) and e (n) waveform Note : in a first implementation of the results are not reflected from a statistical point of view of accuracy of the experimental results ,)

Construct a Low Density Parity Check Matrix for the three code rate of DTMB standart of TDT. The data has obtain of GB2006-20600 paper.

里面包含两个程序，利用这两个程序你实现对于其他程序的处理。非常实用(Which contains two procedures, the use of these two procedures you implement other programs for processing. Very practical)

Calculation of spectral characteristic of 1D PC as a function of refractive index of the layer.

基于灰度共生矩阵的图像特征提取,包括熵、相关性、标准差及方差(Image feature extraction based on GLCM，including entropy, correlation, standard deviation and variance)

说明：  ant colony algorithm jsp using matlab

能做电力系统仿真，风机接入电力系统的仿真计算(Do power system simulation, fan access to power system simulation)

内容：空间目标识别，采用PM算法。程序中附有注释，可以改变方向角，运算速度比music算法快，本人毕设程序，绝对可用。(Content: space target recognition using PM algorithm. Annotated program, you can change the direction of the angle calculation algorithm is faster than the music, I set up the program, absolutely free.)

该程序可以让你通过设置一序列参数来获得具有一定距离的两波源实现干涉(This program lets you set up a sequence of parameters through to get some distance the two wave source to achieve interference)