wavelet

说明：  ltcode编码部分的matlab仿真。(lt coding of matlab simulation.)

WINDTURBINE DFIG STATCOM

基于灰色关联系数的模糊层次分析法。两种方法的综合运用，MATLAB编写，方便实用。(Correlation coefficient based on the fuzzy gray level analysis. Comprehensive use of the two methods, MATLAB prepared, convenient and practical.)

说明：  主元分析法的相关算法，实现主元提取，输入相关 数据即可(PCA analysis of relevant algorithms, to achieve PCA extraction, input the relevant data can be)

1、系统仅处于训练状态。训练序列为2cos(2π×f1×n/fs)， 干扰为sin(2π×f2×n/fs)；序列长度为100个样点。 其中n=0…99，f1=1kHz，f2=2kHz，fs=8kHz。 2、采用LMS算法，均衡器输入为训练序列加上干扰，均衡器阶数为21阶，步长因子β=0.01。 3、在Matlab中编写浮点LMS算法，绘制均衡器的输出波形，并与训练序列进行对比。 (1, the system only in the training status. The training sequence is 2cos (2πf1n/fs), interference sin (2πf2n/fs) sequence length of 100 samples. Where n = 0 ... 99, f1 = 1kHz, f2 = 2kHz, fs = 8kHz. 2, using LMS algorithm, the input to the equalizer training sequence plus interference equalizer order is 21 bands, step factor β = 0.01. 3, the preparation of the floating-point LMS algorithm in Matlab, draw the output waveform equalizer, and with the training sequence comparison.)

一杯沸水冷却，圆柱体模型，底面半径0.05m，高0.1m，周围温度20度，初始水温100度 方程是四维输运方程（常数a^2=k/(c*p)，k是热传导系数0.6006焦/（米*秒*度）） 初始条件：t=0时水等于100度 边界条件：1.上下壁都是自由冷却，第三类边界条件，周围温度保持在20度（H=k/h,h取1） 2.杯壁绝热，第二类边界条件 图形显示格式,取过圆柱轴的截面温度变化将其做成动画. (A cup of boiling water for cooling, the cylinder model, the bottom radius of 0.05m, the high-0.1m, an ambient temperature of 20 degrees, the initial water temperature of 100 degrees is four-dimensional transport equation equation (constant a ^ 2 = k/(c* p), k is the thermal conductivity coefficient of 0.6006 J/(m* s* degrees)) initial conditions: t = 0 when the water equivalent to 100 degrees boundary conditions: 1. up and down the wall are free cooling, the third boundary condition, the ambient temperature maintained at 20 degrees (H = k/h, h check one) 2.杯壁insulation, the second boundary condition graphical display format, check-off section of cylindrical shaft temperature change to make animation.)

进行LTE的SCH的处理程序，在lTE系统的链路级仿真中，发端的设计编程。属于LTE SCH处理。(sch processor)

matlab一百例，有详细的程序讲解，很有用的资料(matlab one hundred cases, explain the procedures detailed, useful information)

简单的仿真过程，通过输入信号，和s函数可以得到一定的仿真结果(Simple simulation process, the input signal, and s functions can get some simulation results)

matlab中关于mfcc函数的程序代码及描述(the matlab Juan Yu fcc Published mustard Note Fei Dong )