HeatMeterbyUsingRL78L12-6901-gp21

说明：  密码锁，矩阵键盘，报警防护系统，stm32(key board stm32 stm32 stm32stm32)

STC12C5A60S使用PCA输出两路PWM程序(STC12C5A60S uses PCA to output two PWM programs)

I2C总线协议应用,利用单片机中断实现可以记忆的时钟,程序自己已经调试过，绝对能用(I2C bus protocol applications, the use of the microcontroller interrupt memory clock, program debugging, and absolutely can)

避障小车红外避障，超声波避障，寻光外加寻迹(Obstacle Avoidance Car Infrared Obstacle Avoidance, Ultrasound Obstacle Avoidance, Light Seeking and External Tracking)

Code is intended to just explain the principle of SPIHT, Arithmetic Coding not Used in this Code Works only for 128 x 128 images, u have to generalize(Code is intended to just explain the principle of SPIHT, Arithmetic Coding not Used in this CodeWorks only for 128 x 128 images, u have to generalize)

K60实现16bitadc采集，可移植性强。(K60 achieve 16bitadc collection, portability.)

刷花的源码，YY协议刷花的源码，大家拿去玩吧(YY brush flowers)

iOS 网络状态监测。网络实时检测，用到Reachability（自行下载）,需加框架:SystemConfiguration.framework ios程序需要用到网络检测，有些程序是刚启动时检测一次，而有些则从头到尾检测网络状态。(IOS network status monitoring.Real-time detection and Reachability (download), frame: SystemConfiguration.framework IOS programs need to use network detection, some detection once when the program is launched, while others detect the network status start to finish.)

说明：  利用ATmega16单片机与4位7段共阴极数码管构成流转灯控制电路(Using ATmega16 single chip microcomputer and 4-bit 7-segment common cathode nixie tube to form the control circuit of flow lamp)

说明：  用C语言编写STM32嵌入式程序，设计一个万年历系统，并用HX1230屏显示相关的时间信息。 基本要求： 1.C语言程序要求是模块化设计。 2.该万年历要求能显示时间（时、分、秒）、年月日及闹钟定时时间（分、秒）。 3.该系统由2-3个按键可调整显示的时间、年月日及闹钟定时时间，具体各个按键功能及编程方式自定。 4.该闹钟可以定时时间到，LED将发出提示闪光，且持续30s。 5.HX1230屏能驱动显示。 6.定时时间可被打断，即打断后恢复时继续计时。 7.设置闹钟报警功能； 8.利用STM32自带的温度传感器功能，使系统能显示当前环境温度值。(STM32 embedded program is written in C language, a calendar system is designed, and relevant time information is displayed on HX1230 screen. Basic requirements: 1. The requirement of C language program is modular design. The calendar requires that time (hours, minutes, seconds), year, month, day and alarm clock timing time (minutes, seconds) be displayed. 3. The system can adjust the display time, year, month, day and alarm clock timing time by 2-3 keys, and the function and programming mode of each key are self-determined. 4. The alarm clock can be scheduled to arrive, and the LED will give a prompt to flash, and lasts for 30 seconds. 5. HX1230 screen can drive display. 6. Timing time can be interrupted, i.e. when the interruption is resumed, the timing will continue. 7. Setting alarm function of alarm clock; 8. Using the temperature sensor function of STM32, the system can display the current environmental temperature)