ADXL345

基于Proteus的8086接口仿真实验,内含实验说明书及代码(Proteus 8086 interfaces based simulation, embedded test specification and code)

数模转换，基于AVR16单片机的程序，基础入门(Digital analog conversion)

说明：  MAX31856测试程序，MSP430F5342通过端口模拟SPI总线操作MAX31856,并将采集到的数据通过UCA1串口发送.硬件上采用隔离电源,隔离通讯接口.多路热电偶信号经多路电子开关选通后再采集.仅供参考,实验室调试通过,未投入实用. 压缩包内容: 1.MSP430程序源代码.包括测试程序及加了协议的多路采集程序. 2.硬件电路图.PDF格式,包括电路板原理图,PCB布局图,元件清单. 3.MAX31856芯片手册及官方例程. 4.PC端程序(通讯协议仿的迅威科技8通道热电偶温度变送器的协议,所以他们的PC端测试程序应该也是可用的) 整理时间:2020年4月15日(MAX31856 test procedure, MSP430F5342 simulates the SPI bus to operate the MAX31856 through the port, and converts the collected data to serial transmission through UCA1. The hardware uses isolated power supply and isolated communication interface. Reform reference, laboratory debugging passed, not occupied practical. Compressed package content: 1. MSP430 program source code. Including test procedures and multi-channel acquisition procedures with added protocols. 2. Hardware circuit diagram. PDF format, including circuit board schematic diagram, PCB layout diagram, component list. 3. MAX31856 chip manual and official routines. 4. PC-side program (the communication protocol is a copy of the Xunwei Technology 8-channel thermocouple temperature threshold protocol, so their PC-side test program should also be available) Arrangement time: April 15, 2020)

利用单片机MSP430f149单片机实现的 实验八 ADC与LCD(The use of single-chip MCU MSP430f149 experiment eight ADC and LCD)

笔段式LCD驱动方法，利用单片机直接驱动，无需外加芯片(A LCD driving method, the use of single-chip drive directly, without the need of additional chip )

二氧化锆氧气传感器的氧气含量测量程序（此程序已经应用到产品）(Procedures for the measurement of oxygen content of two zirconia oxygen sensor (this procedure shall be applied to the product))

DHT11检测温湿度同时显示在LCD1602的代码(DHT11 detects the temperature and humidity while displaying the code on the LCD1602)

This test does only covers cases where the Additive or Mulplicative expression ToPrimitive is a string.

在电力系统仿真软件PSCAD中构建的光伏阵列的仿真模型，对新能源太阳能电池并网的研究有很大作用(Build the simulation model of the PV array power system simulation software PSCAD, new energy solar cell grid research)

本文以霍尔茨(HOLZER)法作为船舶轴系扭转振动的计算方法，着重研究了船舶轴系自由扭振的计算与分析，并对轴系扭振产生原因进行了分析，提出了一系列减振方法，以保证船舶动力装置的安全正常运行。(In this paper, Holtz (HOLZER) Act as the ship shafting torsional vibration calculation methods, focusing on the calculation and analysis of ship shafting torsional vibration of freedom, and the shaft torsional vibration causes analyzed, proposed a series of less vibration methods to ensure the safety of the ship s power plant running.)