Voice-signals-pitch-detection

经典书籍《软件定义的GPS和伽利略接收机》一书代码，讲述GNSS软件接收机整个流程，可以把数据直接导入。(Classic Books " software-defined GPS and Galileo Receiver," a book code, about the whole process GNSS software receiver, you can import the data directly.)

IEEE所有标准系统的局部电压稳定（L指标）计算的通用程序！适用于任何节点。(IEEE standard system L index calculation of the general program!)

说明：  一个4*8天线数的mimo仿真程序，采用16QAM调制解调，在平坦衰落环境下的误码率情况(a 4* 8 the number of MIMO antenna simulation program using 16QAM modulation and demodulation, the decline in flat environment of the BER)

说明：  8. 单径瑞利信道中的四发四收V-BLAST： (1) 请设计一种具体的导引辅助的信道估计方法，用Simulink进行仿真，测量16QAM调制时的误码率性能。画出比特信噪比与信道估计均方误差的关系曲线，画出比特信噪比与误码率的关系曲线。 (2) 计算所设计方案的频谱效率是多少，单位为bit/Hz/s。(8. Four transmit four receive v-blast in single-path Rayleigh channel: (1) please design a specific navigation-assisted channel estimation method and conduct simulation with Simulink to measure the bit error rate performance of 16QAM modulation.The relation curve between the bit signal-noise ratio and the mean square error of channel estimation is drawn, and the relation curve between the bit signal-noise ratio and the bit error rate is drawn. (2) calculate the spectral efficiency of the designed scheme in bit/Hz/s.)

Fe-Cu-Mn-Ni析出行为的相场模拟---matlab程序(phase-field simulation of precipitation behaviour of Fe-Cu-Mn-Ni alloy)

在三条径的瑞利信道中，对于直接序列扩频： (1) 请设计DS-CDMA一种具体的码分导引辅助的信道估计方法，接收机分别采用等均益合并、最大比合并。用Simulink进行仿真，测量BPSK的误码率性能，画出比特信噪比与信道估计均方误差的关系曲线，画出比特信噪比与误码率的关系曲线，请解释在误码率为0.01时，两种合并方式所表现的不同的物理意义。 (2) 设频率已经同步，请设计DS-CDMA一种具体的单停顿滑动相关时间同步方法，用Simulink进行仿真(自己编写代码S-Function方式)，分析所设计方案的时间同步精度，画出比特信噪比与捕获概率的关系曲线。 (3) 设时间已经同步，请设计DS-CDMA一种具体的频率方法，用Simulink进行仿真(自己编写代码S-Function方式)，画出比特信噪比与频率同步误差的关系曲线。 (err)

digital signal processing correlation technique

MIMO系统的多径信道仿真程序，带有接收端和发送端的相关性计算，符合非物理模型下的MIMO信道(MIMO system in multipath channel simulation program, with the receiving end and sending end of the relevant terms, in line with the non-physical model of the MIMO channel)

研究d2d通信加中继节点来优化蜂窝小区边缘用户通信，并通过MATLAB仿真(The D2D communication and relay nodes are studied to optimize the edge user communication of cellular cell, and the simulation is carried out by MATLAB.)

说明：  利用matlab/simulink搭建仿真模型，模拟高压整流输电24脉波整流器(Using Matlab / Simulink to build a simulation model to simulate the 24 pulse rectifier of high voltage rectifier)