-
FT
说明: DSP入门:在MATLAB中应用傅里叶变换分析信号频谱(DSP basis: Implement fourier transform to analysis signals spectrum with MATLAB)
- 2010-03-25 13:39:45下载
- 积分:1
-
virdo
locating the same in different parts of your disks
- 2010-12-03 20:48:52下载
- 积分:1
-
Pic2Avi
说明: 用MatLab将众多图片文件自动生成avi电影文件(Make a avi file from many picture file using Matlab program)
- 2009-08-15 15:18:16下载
- 积分:1
-
Modern_signal_processing
本书系统全面的介绍了现代信号处理的主要理论,具有代表性的方法和一些典型应用(The book is systematic and comprehensive introduction to the modern signal processing theory, representative methods and some typical applications)
- 2012-05-30 11:04:31下载
- 积分:1
-
STAR_Demonstration
Demonstration for the STAR (Spike-Temporal-Auditory-Analysis)method of neural coding utilized in cochlear implants.
- 2014-09-05 01:24:34下载
- 积分:1
-
IA_MU_MIMO_OFDM_Version_1
基于ofdm-mimo系统,认知无线电干扰对准的两种算法对比。 MMSE和minimized leakage interference.(interderence alignment algorithms of cognitiv radiao,based on OFDM MIMO system.)
- 2013-12-03 00:16:06下载
- 积分:1
-
task31
说明: 工序调整:因为实际因素的影响,在任务11开始之前必须先完成任务15,而在任务9(顶部施工)开始到第7周后必须穿插1周时间的安装工作,因而任务10中的“照明系统”工作周数也相应减少1周;(Adjustment process: since the actual factors, the task must be completed 11 missions before the start of 15, while in task 9 (top construction) began to be interspersed 7 weeks 1 week after the installation time, thus the task of 10 in " lighting systems " work week is also a corresponding reduction in the number of 1 week )
- 2010-03-31 10:50:35下载
- 积分:1
-
模糊熵
说明: 计算模糊熵值,在样本熵的基础上进行改进的模糊航,计算时间序列的复杂性(Computable Fuzzy Entropy Value.An improved fuzzy navigation based on sample entropy is used to calculate the complexity of time series.)
- 2019-03-26 18:25:26下载
- 积分:1
-
chapter5
于慧敏信号与系统第二版第五章部分习题的matlab代码... (And systems in Huimin Xin No. Part Second Edition Chapter Exercises matlab code ...)
- 2010-06-04 11:01:45下载
- 积分:1
-
dual_core
This example application shows you how to use Real-Time Workshop Embedded Coder to target a dual core Blackfin microprocessor. The complete build is managed by a template makefile and control over the memory regions is provided by custom storage classes. The example imposes a top level architecture on the model to define the split of model code between the two cores. This document describes a complete run-through of the model from Simulink simulation to code simulation using VisualDSP. I think it will take about 1 hour to go through the example once you have VisualDSP installed.
- 2010-01-09 16:47:58下载
- 积分:1