bus-load-data

利用定时器产生PWM，使LED灯由亮到灭，由灭到亮逐步变化( Use timer produce PWM, make the light to destroy LED lamp, the gradual change to light out )

PSCAD做的风电变流器网侧变换器，7断式svpwm调制，运行良好。(PSCAD do wind power inverter side converter, 7 broken type SVPWM modulation, work well.)

万年历开发 时间Calendar Development - Time(Calendar Development- Time)

51单片机开发步进电机源代码及报告解释说明(a progress of 51MCU introduction)

一款电厂巡检软件，很简单的C++处理程序，适合初学者使用，C++(A plant inspection software, very simple C++ handler for beginners, C++)

本作品以MSP430单片机为核心， 基于DDS原理，通过查表方式输出步进量为10HZ，频率为100HZ~2KHZ的正弦波。两路被测信号通过过零比较、异或和低通滤波整流，实现了对相位差的测量，误差小于(This works with MSP430 microcontroller as the core, based on DDS principle, by look-up table output step sizes for the 10HZ, frequency of 100HZ ~ 2KHZ sine wave. Two by the signal zero-crossing comparator, XOR, rectification and low-pass filtering, the realization of the phase of the measurement error is less than)

说明：  一个自写的ClistCtrl打印类，直接引用就行(a written ClistCtrl Print category applied directly on the line)

PIC （PIC16F886） 做的简单频率计 用TMR0定时1s，将待测信号从T1CKI脚输入，用TMR1进行计数，读出TMR1H，TMR1L的值就是频率 单片机：PIC16F886 显示：LCD1602 编程语言：PIC C 附Proteus仿真。(PIC (PIC16F886) to do a simple frequency counter TMR0 timer with 1s, the test signal input pin from T1CKI with TMR1 count, read TMR1H, TMR1L value is the frequency of the microcontroller: PIC16F886 display: LCD1602 with Proteus simulation.)

步进电机28BYJ48型四相八拍电机，电压为DC5V—DC12V。当对步进电机施加一系列连续不断的控制脉冲时，它可以连续不断地转动。每一个脉冲信号对应步进电机的某一相或两相绕组的通电状态改变一次，也就对应转子转过一定的角度（一个步距角）。当通电状态的改变完成一个循环时，转子转过一个齿距。四相步进电机可以在不同的通电方式下运行，常见的通电方式有单（单相绕组通电）四拍（A-B-C-D-A。。。），双（双相绕组通电）四拍（AB-BC-CD-DA-AB-。。。），八拍（A-AB-B-BC-C-CD-D-DA-A。。。）(Stepping Motor 28BYJ48 four-phase eight-phase motor, the voltage DC5V-DC12V. When a series of continuous control pulses are applied to the stepper motor, it can be continuously rotated. Each pulse signal corresponds to the stepper motor of a phase or two-phase winding power state change once, also corresponds to the rotor through a certain angle (a step angle). When the change in the power-on state completes one cycle, the rotor turns one pitch. Four-phase stepper motors can be operated in different power-up modes. The common power-up modes are: single-phase winding power (ABCDA ...), double (dual-phase winding)-DA-AB-...), eight beats (A-AB-B-BC-C-CD-)

99秒马表，在Proteus设计两个数码管动态显示及一个键盘SP。在ucos下结合keil完成开始时，显示“00”，第1次按下SP后就开始计时。 第2次按SP后，计时停止。第3次按SP后，计时归零。 (99 seconds stopwatch, two in the Proteus design dynamic digital tube display and a keyboard SP. Keil in combination ucos completed under the beginning of the show " 00" , 1st timer after pressing the SP. 2nd by SP, the time to stop. The 3rd by the SP, the time zero.)