Imager_SDK_14.12.20086

温湿度报警系统，基于VB的小程序，和DHT11相关。(Temperature and humidity alarm system, VB-based applets, and DHT11 related.)

很适合英飞凌单片机的初学者，可作为初学者的很好的参考资料。(Infineon microcontroller is suitable for beginners, as a good reference for beginners.)

步进电机28BYJ48型四相八拍电机，电压为DC5V—DC12V。当对步进电机施加一系列连续不断的控制脉冲时，它可以连续不断地转动。每一个脉冲信号对应步进电机的某一相或两相绕组的通电状态改变一次，也就对应转子转过一定的角度（一个步距角）。当通电状态的改变完成一个循环时，转子转过一个齿距。四相步进电机可以在不同的通电方式下运行，常见的通电方式有单（单相绕组通电）四拍（A-B-C-D-A。。。），双（双相绕组通电）四拍（AB-BC-CD-DA-AB-。。。），八拍（A-AB-B-BC-C-CD-D-DA-A。。。）(Stepping Motor 28BYJ48 four-phase eight-phase motor, the voltage DC5V-DC12V. When a series of continuous control pulses are applied to the stepper motor, it can be continuously rotated. Each pulse signal corresponds to the stepper motor of a phase or two-phase winding power state change once, also corresponds to the rotor through a certain angle (a step angle). When the change in the power-on state completes one cycle, the rotor turns one pitch. Four-phase stepper motors can be operated in different power-up modes. The common power-up modes are: single-phase winding power (ABCDA ...), double (dual-phase winding)-DA-AB-...), eight beats (A-AB-B-BC-C-CD-)

基于51单片机的PT2314音频功放程序，可实现MIC和音频输入切换及音量音调控制，并用5110显示(Based on 51 single-chip audio amplifier PT2314 program can achieve MIC and audio input switching and volume tone control and display with 5110)

一个数字梯形，选择k条路线，每条路线从第一层的某个数开始，每次进入下一层到达左下或者右下的数字，直到最后一层为止。每条路线不能经过相同的路径，但是可以经过相同的数字节点。 输出一个整数，表示能得到的最大的k条路径经过的数字之和(A digital ladder, the K route, each route the first layer of a number, each time to enter the next layer to reach the left or right next to the number, until the final layer. Each route can not pass through the same path, but can pass through the same number of nodes. Output an integer representing the sum of the number of the largest K paths that can be obtained)

ht1621驱动C语言版本,基本是一个通用的版本(ht1621 driver C language version of the basic version is a generic)

单片机 8051 C语言 温度传感器DS18B20(SCM 8051 C language temperature sensor DS18B20)

自动交通控制系统用红、绿、黄三支共两组发光二极管表示交通信号灯，利用单片机模拟有时间显示的定时交通信号灯控制管理。信号灯的变化规律可如下： 1）放行线：绿灯亮放行25秒，黄灯亮警告5秒，然后红灯亮禁止。 2）禁示线：红灯亮禁止30秒，然后绿灯亮放行。 3）当某一方向的红灯亮时，若该方向有车通过，则用扬声器声报警。（撞红灯信号可用3-5V模拟量表示）(Automatic traffic control system using red, green, yellow light-emitting diodes, said a total of three traffic lights, the use of single-chip analog time display on a regular traffic signal control and management. Changes of lights to be as follows: 1) Release Line: green clearance 25 seconds, the yellow light warning for 5 seconds, then the red light is prohibited. 2) ban shows lines: the red light is prohibited for 30 seconds, then the green light to release. 3) When the red light in one direction, if the direction of the car through, the alarm speaker sound. (Hit the red signal available 3-5V analog representation))

梦幻古龙2.5D网游全套完整源码 梦幻古龙2.5D网游全套完整源码 梦幻古龙2.5D网游全套完整源码 梦幻古龙2.5D网游全套完整源码(C++ LUA混合而成 )

此程序为利用Kinect v2实现用手指隔空控制鼠标,效果非常好。 运行环境 Kinect for Windows V2 Kinect SDK 2.0 OpenCV 3.0(This program is implemented with the use of Kinect v2 finger Taking control the mouse, the effect is very good. Operating environment Kinect for Windows V2 Kinect SDK 2.0 OpenCV 3.0)