fir-gui

统一设定带宽、脉宽、采样率、脉冲重复频率，用Matab产生16个脉冲的LFM，每个脉冲有4个目标（低速，静止，高速，低速），第3个目标的距离、速度与学号有关。前3个目标的幅度相同，第四个目标幅度是前三个的一半。且距离与第2个静止目标相同。 依次做如下处理： 1 脉压 2 脉压后，相邻2脉冲做MTI（即相邻2个脉冲对应相减），产生15个脉冲 3 脉压后，16个脉冲到齐后，做MTD，输出16个多普勒通道 4 对MTD结果做CFAR（恒虚警） (Unified set bandwidth, pulse width, sampling rate, pulse repetition frequency, and produces 16 pulses Matab LFM, with four goals each pulse (low-speed, static, high-speed, low speed), the first three goals of distance, speed and Student ID related. The first three goals of the same magnitude, and the fourth target range is half of the first three. And from the stationary target with the first two the same. Followed by treatment as follows: 1 pulse 2 pulse pressure, the adjacent two pulses do MTI (that is adjacent to two pulses corresponding to the subtraction), resulting in 15 pulse 3 pulse pressure, 16 pulses in attendance after doing MTD, 16 Doppler channel output 4 MTD results do CFAR (CFAR))

本程序是自己写的，在瑞丽衰落信号下的BPSK仿真，已经经过试验成功(This program is written in their own, in Ruili fading BPSK simulation signal, has been successfully tested)

说明：  基于MATLAB的多类型电动汽车充电负荷仿真模型(electric vehicle charging load simulation based on MATLAB )

jpeg在matlab下的仿真实现，整个程序运行还行，共享给大家(jpeg of the Matlab Simulation, and the whole process has run OK, for everyone to share)

Helps in learning MATLAB programming

一种在盲源分离中用到的互信息最大化Ica算法的matlab程序(Mutual information maximization Ica used a blind source separation algorithm matlab program)

直线感应电机的 matlab的pid控制 观察其稳定性(PID control of lin Observe the stabilityear induction motor matlab )

单一频率的正弦相关法动态测试系统的测试方法简单，不需要对系统进行辨识。只需要观察被测系统输出信号的相差和幅值变化。通过扫频的方法测量在不同的频率点下的幅值和相位变化。在工程应用中，只需要知道被测系统的相位变化在正常的范围内就可以视系统的动态性能正常。该仿真算法只是建立了一个模型。在实际运用时还需要变换测试信号的频率和周期。(A single frequency sinusoidal correlation method of testing dynamic testing system is simple, does not require system identification. Only need to observe the difference between the measured system output signal and amplitude change. Swept through the method of measurement points at different frequencies under the amplitude and phase changes. In engineering applications, only need to know the system under test changes in the normal phase it may be possible within the framework of the dynamic performance of the system to normal. The simulation algorithm is the establishment of a model. In the practical application of test signals also needed to change the frequency and periodicity.)

说明：  在模式识别应用中，用分支定界法(branch-and-board method)进行特征的选择。该程序在matlab环境下实现了该算法，以从六个特征中选择两个最佳特征为例(In pattern recognition applications, using branch and bound method (branch-and-board method) to carry out the characteristics of choice. The program in the matlab environment to achieve the algorithm to select from the following six characteristics of the best features of the two as an example)

元胞自动机仿真车道车流情况，可以显示图像，可以成功编译(Cellular automata can simulate traffic flow in lanes, display images, and compile successfully.)