libsvm-mat

模糊工具箱的说明，MATLAB。很有用哦(Description of fuzzy toolbox, MATLAB. Oh, very useful)

光伏电池阵列输出功率受光照强度和温度变化的影响，因此最大功率点跟踪（MPPT）技术广泛应用于光伏系统中。在所有最大功率点(MPP)控制策略中，扰动观察（P&O）MPPT算法因易实现被广泛应用，然而它的缺点是在稳定工作状态下工作点通过MPP 时会导致能量振荡损耗，并且在光照强度或温度发生突变时表现较差的动态响应。在本文中，提出一种改进型变步长扰动观察MPPT 算法，此方法依据工作点动态调整步长变化，与传统固定步长方法比较，本文提出的方法能有效地提高MPPT 速度和转换效率，通过仿真和实验结果分析，验证了此改进算法的可行性。(PV array output power by light intensity and temperature changes, so the maximum power point tracking (MPPT) technology is widely used in photovoltaic systems. In all the maximum power point (MPP) control strategy, the perturbation and observation (P & O) MPPT algorithm because easy to implement is widely used, but its disadvantage is the steady-state operating point by the MPP causes energy oscillations loss, and in the light intensity or temperature mutated poor performance dynamic response. In this paper, we propose a modified variable step size perturbation and observation MPPT algorithm, this method is based on dynamically adjusting the operating point changes in steps, with the traditional fixed-step methods, the proposed method can effectively improve the speed and efficiency MPPT, The simulation and experimental results verify the feasibility of this algorithm.)

简要的介绍了在matlab中如何将gui转换为exe可执行文件(A brief introduction of how to convert the gui to exe executable file in matlab)

说明：  本文章阐述了如何产生m序列，对初学者是一份很重要的资料(This article describes how to generate m sequence, for beginners is a very important information)

buck电路的matlab仿真，单环控制(matlab simulink of buck circuit)

It is code for mir testing

Used function P(x) = 1+x− x2+0.2x3+0.1x4 and its known the values P(x)=[ -6.2 -8.3 -5.0 -1.1 1 1.3 2.2 8.5 27.4], in x= [-4 -3 -2 -1 0 1 2 3 4] to interpolate in the xi = − 4 + 0.1i, i = 0, 1, 2, . . . 80. Results are graphically compared!(Used function P(x) = 1+x− x2+0.2x3+0.1x4 and its known the values P(x)=[-6.2-8.3-5.0-1.1 1 1.3 2.2 8.5 27.4], in x= [-4-3-2-1 0 1 2 3 4] to interpolate in the xi = − 4+ 0.1i, i = 0, 1, 2, . . . 80. Results are graphically compared!)

说明：  基于遗传算法（GA）设计了pid控制器，仿真结果良好。(based on genetic algorithm (GA) pid controller design, simulation good results.)

仿真了盲辨识RLS和LMS算法的时间平均信干比，分析了两者的多址干扰抑制能力(Simulation of the blind identification algorithm RLS and LMS average signal to interference ratio of the two algorithms of multi-access interference suppression)

生成余弦函数分布的条纹图，并且分别储存在四幅图中！(Generate a cosine function distribution of the fringe pattern, and were stored in the four figure!)