Fuzzy-Control-Systems

说明：  《Fuzzy Relational Calculus Toolbox, Rel.1.01》The toolbox provides functions and original algorithms for solving direct and inverse problems. Author: Yordan Kyosev & Ketty Peeva("Fuzzy Relational Calculus Toolbox, Rel.1.01" The toolbox provides functions and original algorithms for solving direct and inverse problems. Author : Yordan Kyosev Ketty Peeva)

此程序是描述的RSSI曲线的代码 重点与A值和n值的关系！(the relationship between the parameters of the n and A in RSSI)

WIMAX_WZ_withencoding:信道估计，相位噪声补偿，频偏估计，编解码都有 WIMAX_WZ_withoutencoding：在上面的工程基础上，去掉编解码部分 WIMAX_WZ_withoutprocessing：在上面的工程基础上，再去掉相位噪声补偿，频偏估计 WIMAX_WZ_withoutprocessing2：在上面的工程基础上，改用新的前导和导频联合信道估计方案,参考文档《基于802_16d标准的OFDM信道估计技术的研究与实现.kdh》 因为白噪声信道仿真只能体现QPSK调制和RS-CC编码的性能，需要仿真SNR可控的SUI信道，来估计信道均衡的性能。 在多普勒频偏fd>100Hz时，联合信道估计性能才比前导估计强，否则前导估计性能更优。对于600MHz中心频率，要求收发机相对运动速度大于180km/h，这种情况出现的概率不大(WIMAX_WZ_withencoding: channel estimation, phase noise compensation, frequency estimation, the codec has WIMAX_WZ_withoutencoding: the project on the basis of the above, remove the codec section WIMAX_WZ_withoutprocessing: the project on the basis of the above, then remove the phase noise compensation, offset estimation WIMAX_WZ_withoutprocessing2: In the project on the basis of the above, use the new leader and pilot joint channel estimation scheme, the document " Standards-based 802_16d OFDM channel estimation and implementation of technology .kdh" because white noise channel simulation only reflects the QPSK modulation and RS-CC coding performance requires simulation SNR controllable SUI channel, to estimate the performance of channel equalization. When Doppler shift fd> 100Hz, joint channel estimation performance was stronger than the leading estimate, otherwise better estimation performance leader. For 600MHz center frequency transceiver requirements relative velocity )

Galton 板钉问题的matlab实现，压缩包中两个文件，一个用于算法实现，一个用于绘图。(Matlab implementation of the Galton board nail compressed package in two files, one for the algorithm, one for drawing.)

用matlab实现三次NURBS插值曲线拟合，插值源程序(Using matlab to achieve Cubic NURBS interpolation curve fitting, interpolation source)

这是一个无线传感器网络的Rage-Free的定位算法，用matlab进行仿真实现！方便初学者参考使用！(This is a wireless sensor network, Rage-Free positioning algorithm using matlab simulation to achieve! Convenient reference for beginners to use!)

在转速为48K/min时，正常工况下的时域波形(In speed for 48 k/min, the normal working conditions of the time domain waveform )

说明：  主成分析在matlab中应用有源程序,关于主要因素的提取(Principal Component Analysis in matlab application has source code, the main factors on the extraction)

说明：  使用软件的实现EQ均衡器算法，可以调节多段EQ(The realization of the use of software EQ EQ algorithm can adjust the multi-segment EQ)

说明：  基于matlab的G-P算法计算关联维数(Based on the GP algorithm matlab correlation dimension)