QAM16_simulink

数字通信仿真程序，BPSK调制在高斯白噪声信道下的误码率分析。(digital communications simulation program, BPSK modulation in Gaussian white noise channel BER analysis.)

通过确定执行边界的方法计算美式期权价格，并画出它的执行边界。(Determine the implementation of the boundary of the method to calculate the American option price and draw the boundary of its execution.)

结合25个实例，详细介绍了matlab的编程技巧(The combination of 25 instances, details Matlab programming skills)

用过完备字典的压缩感知进行频率估计，画出频谱图(Compressed sensing frequen cy estimation)

基于Matlab的神经网络工具箱应用使用情况简介(Based on Matlab neural network toolbox of the application of the use of brief)

BER in WCDMA simulation

四元数matlab程序中的FFT计算程序，很好很强大的(Quaternion FFT matlab program calculation program, very good very strong)

EasyMod is a MatLab/Scilab toolbox for teaching modal analysis. It provides a set of functions allowing to establish the identification of modal parameters and these validation. Nowadays, circle-fit, line-fit and least square complex exponential methods are implemented. In addition, some relevant functions are offered in order to complete a modal analysis: operations on the frequency response function (FRF) , generation of FRF from mass, damping and stiffness matrices, MAC (modal assurance criterion) and modal collinearity

数学建模中国人口结构预测模型递推公式Matlab源程序(Mathematical modeling of China' s population structure prediction model recursive formula Matlab source)

小波变换进行变速箱故障诊断 首先将s1和s2信号时域谱（s1代表维修前的振动信号，s2代表维修后的振动信号），画出来进行对比，会发现s1信号的振动幅值会比较高；然后对s1和s2分别进行小波分解并画出各层的时域谱，只对比s1和s2分后的最高时域谱，s2更加的具有周期性，且幅值较小，s2周期性不够明显，且振动过于密集。分析完时域谱后开始分析频谱，首先对原信号s1和s2fft转换，得到频谱图，如图，然后再对小波分析后高频部分进行fft转换，做出频谱图。对比后我们发现，在f 2375HZ出（也就是齿轮的啮合频率），s1信号频谱幅值会有急剧的升高，然后，其谐波的幅值也会增大。所以可以推断出该维修前的增速箱的齿轮可能出现问题。(Gearbox fault diagnosis based on wavelet transform s1 and s2 first time domain signal spectrum (s1 behalf of the vibration signal before maintenance, vibration signal s2 representative of repaired), drawn comparison, you will find a signal s1 vibration amplitude will be higher then s1 and s2 respectively wavelet decomposition and draw the layers of time-domain spectrum to only a maximum time domain spectroscopy s1 and s2 points after, s2 is more cyclical and smaller magnitude, s2 cyclical enough obviously, and the vibration is too dense. End domain spectral analysis after the beginning of the spectrum analysis, the first of the original signal s1 and s2fft conversion to give the spectrum, as shown, and then after the high frequency part of wavelet analysis fft transformation to make spectrum. We found that after the comparison, at f 2375HZ out (i.e. the gear mesh frequency), there will be a sharp increase in the amplitude spectrum of the signal s1, and then, the amplitude of the ha)