occupy

objective optimization algorithm matlab codes

使用Matlab开发的设计凸轮的源程序，使用了向量法的设计方法。设计了一个正弦运动规律的凸轮，程序带有较完整的注释，对于初学凸轮设计的人来说应该是一个比较好的参考。(It s the source code of the design of a cam using matlab, which uses the method of vector.)

我找到的学习MATLAB的资料和大家分享一下希望能给大家一些帮助(I am learning MATLAB to find information and share with you hope to give you some help)

用Matlab对经过与处理后的车牌图像进行分割的程序，可以很好的分割车牌，把各个车牌字符都分割出来(Matlab right after dealing with the license plate image segmentation procedures, can good segmentation plates, license plate characters are all split up)

recative power pricing national conference paper is present inside

平滑秩序列法估计相干信号源数目，包含信号源模型的建立和MDL准则的仿真(Smooth Rand Profile estimates the number of coherent sources, including the signal source modeling and simulation of MDL standards)

demo OceanOptics communication systems.

首先提出了基于微分几何控制理论的双馈发电机非线性多输入多输 状态反馈解藕控制方案，通过非线性坐标变换和非线性状态反馈，使双 发电机的磁链和转速两个子系统实现了动态完全解藕。其次采用基于定 磁场定向的双馈发电机矢量控制，实现定子侧有功功率和无功功率的解藕 为了消除交叉藕合电动势对发电机参数的影响，采用内模控制解藕控制 案，使系统具有良好的输出动态性能。最后在分析双馈发电机的数学模 和矢量控制的基础上，提出了一种基于模型参考自适应方法的定子、转 磁链观测、发电机转速估计和转子电阻辨识算法，应用Lyapunov原理证 了估计的收敛性，并应用于上述解藕控制方案中。在对算法进行理论推 的基础上，应用Matlab/simulink，对各个算法和系统进行了仿真，检验了 算法和控制方案的可行性。 (First proposed nonlinear multi-input multi-input state feedback the decoupled control programs through nonlinear coordinate transformation and nonlinear state feedback control theory based on differential geometry doubly-fed generator, dual generator flux and speed sub-systems to achieve the dynamic completely decoupled. Secondly, based on the fixed magnetic field oriented vector control of doubly-fed generator stator side active power and reactive power decoupling in order to eliminate the cross-coupling of the electromotive force of the generator parameters using the internal model control decoupling control case, so that the system which has good dynamic performance. Finally, in the analysis of the doubly-fed generator based on the mathematical model, and vector control, a method based on the model reference adaptive stator, turn flux observer, generator speed estimation and rotor resistance identification algorithm using the Lyapunov principle permit estimated convergence, and appl)

针对常规PID控制不具有自适应能力，对于时变、非线性系统控制效果不佳。提出了将模糊技术与PID控制相结合的控制方式，设计模糊控制器。(Conventional PID control with adaptive capabilities, time-varying, nonlinear system control ineffective. Fuzzy and PID control combined control mode fuzzy controller design.)

在EFI架構下寫一隻PPI sample(PEIM to PEIM Interface),使兩隻PEIM可透過此PPI互相傳遞資料. Write a PPI sample to make two PEIMs able to communicate each other.(Write a PPI sample to make two PEIMs able to communicate each other.)