06826929-new

格子BLOTZMANN方法，两相流 matlab程序(Lattice BLOTZMANN method, two phase flow matlab program)

频率细化技术在超低频/极低频电磁信号检测中的应用(Frequency refinement technique in ELF/low frequency electromagnetic signal detection)

Mysmo.mdl 永磁同步电机的主程序，可以实现有速度传感器启动运行，和无速度传感器运行。 SMOmodel.m 改进的滑模观测器模型，实现永磁同步电机反电动势的估算。 PFCDCM0hm5 用的是0.5hm的电感，实现220V交流电变换成400V的直流电，电流断续。 由于是仿真，如果要硬件实现的话，除了需要电压采样外，还需要一个输入电压过零检测 PFCCM320percent98k50 用的是5hm的电感，实现220V交流电变换成320V的直流电，电流连续。功率因数可以达到0.98，用的开关频率为50K PFCCM400percent97k50.mdl 用的是5hm的电感，实现220V交流电变换成400V的直流电，电流连续。功率因数可以达到0.97，用的开关频率为50K (Permanent magnet synchronous motor Mysmo.mdl main program, you can achieve the speed sensor up and running, and speed sensors run. SMOmodel.m improved sliding mode observer model permanent magnet synchronous motor back-EMF estimates. PFCDCM0hm5 with is 0.5hm inductor to achieve 220V AC transform into a 400V DC current is interrupted. As the simulation, hardware implementation, then, in addition to the voltage sampling an input voltage over zero detection PFCCM320percent98k50 the is 5hm inductance to achieve transformation 220V AC 320V DC continuous current. The power factor can reach 0.98, the switching frequency for 50K PFCCM400percent97k50.mdl with is 5hm inductance 220V AC transform 400V DC continuous current. The power factor can reach 0.97, with the switching frequency is 50K)

替代数据法中最重要的文献和文献相关的软件代码，非常经典亚(alternative method of data the most important literature and the literature related to the software code, very classic Asia)

两路实数FFT的matlab仿真。硬件实现：一个FFT核实现两路实数FFT。(FFT of two real numbers matlab simulation. Hardware: FFT core to achieve a two-way real FFT.)

双容水箱的液位控制问题。首先对被控对象的模型进行分析，并采用实验建模法求取模型的传递函数。其次，设计PID控制器，在Matlab/Simulink环境下建立双容水箱控制的仿真模型，对PID控制算法进行仿真研究。通过仿真实验，证明该设计方法可行性和该算法的正确性。最后完成了基于PLC的双容水箱液位控制的软硬件设计，编写了PLC梯形图实现了水箱液位的PID控制。(Dual tank water level control problems. First, the controlled object model for analysis and modeling approach using experimental strike transfer function model. Secondly, the design of PID controller, simulation model dual tank water control in Matlab/Simulink environment, PID control algorithm simulation. Simulation results show that the design feasibility and correctness of the algorithm. Finally completed the hardware and software design of PLC-based dual-tank water level control, the preparation of the PLC ladder to achieve the tank level PID control.)

Convert image to vector

地震数据速度库转换程序，matlab编写，可以实现不同速度类型之间的转换(Seismic data speed database conversion program。matlab。Conversion between different speed types)

koding of ofdm reley chanel. multipath chanel

关于FIR低通滤波器的C语言程序设计以及MATLAB程序设计，仿真验证通过(About the C Programming Language FIR low-pass filter MATLAB programming, simulation validation by)