PID-Control

LabVIEW编写的一个信号发生器程序，可选择正弦波、方波、三角波等(A signal generator program written by LabVIEW can select sine wave, square wave, triangle wave, etc.)

峭度指标是非平稳信号故障诊断的重要参数。峭度指标对信号中的冲击成分十分敏感，冲击成分能量越大，其峭度值就会越大，在故障诊断的时域分析中十分重要。本文件中将其独立做成了一个子vi，便于程序直接调用。(Kurtosis index is an important parameter of non-stationary signal fault diagnosis. The kurtosis index is very sensitive to the impact component in the signal. The greater the energy of the shock component, the greater the kurtosis of the signal, and it is very important in the time domain analysis of the fault diagnosis. This document will be independent of a sub VI, to facilitate direct calls to the program.)

航空航天通信技术一般采用模拟通信的频率调制和数字通信的移相键控调制方法。这有利于充分应用信道带宽和能源。频率调制是在一定程度上改变载波或副载波的频率来传输信息的调制方法。移相键控调制是利用载波或副载波的相位跳变来传输信息的调制方法。移相键控又分二相移相键控、四相移相键控和多相移相键控，其中以四相移相键控和八相移相键控调制方法的效率较高(Aerospace communications technology commonly used analog communication of frequency modulation and the digital communication phase shift keying modulation method. This is helpful for making full use of channel bandwidth and energy. Frequency modulation is changed to some extent carrier or subcarrier frequency to transmit information modulation method. Phase shift keying modulation is the use of carrier or subcarrier phase jump to transmit information modulation method. Phase shift keying and binary phase shift keying, four phase shift keying and multiple phase shift keying, of which four phase shift keying and eight phase shift keying modulation method of high efficiency )

labview大学教程配套光盘，含源代码和一些PDF文件(LabVIEW University Tutorial CD CD source)

基于labview的风电轴承故障检测与监测(Wind power bearing fault detection and monitoring based on labview)

该VI已把电机动态模型封装成一个模块,因此使用者不必关心电机的内部结构,只需输入电机的各参数就可以方便地进行仿真,而且仿真的各种变量结果稳定可靠,并可以根据需要,调节仿真步长,提高仿真的精度。 (The dynamic model of the motor VI has packaged into a module, so users do not care about the internal structure of the motor, simply enter the motor parameters can easily be simulated, and the simulation results of various variables stable and reliable, and may need , adjust the simulation step, to improve the accuracy of the simulation.)

开发板stm32 labview tcp/ip通讯程序，测试ok(Development board stm32 labview TCP/IP communication program, test ok)

说明：  基于NI的LABVIEW开发平台的数字示波器开发实例(Development Example of LABVIEW Digital Oscilloscope)

Labview的小波分解与还原程序，没有调用matlab，配套论文，可以此为基础改成小波去噪程序(Labview wavelet decomposition and reduction program, there is no call matlab, supporting the thesis, this can be changed based on wavelet denoising procedure)

说明：  FOR循环计算0——99偶数的和，用到for循环以及移位寄存器(FOR loop calculates the sum of 0-99 even numbers, using for loop and shift register)