practical_fir_filter_design_in_matlab

矢量控制解耦模型比较仿真，主要包括反馈解耦，前匮解耦，和交叉解耦三种模式。(Simulation of vector control decoupling model comparison)

由设计要求可知，wp<=0.2π，允许误差幅度小于1dB，ws>=0.3π内衰减应大于15dB。为了验证数字滤波器的实际滤波功能，设计程序时，把输入序列定为验证函数x（t）=4sin（100πt）以及x（t）=4sin（200πt）和x（t）=4sin（400πt）。又因为Ts=1.25ms，T=80ms，故采样点为64，即N=64，所以当M=6，可以同时调试并验证程序的滤波功能。(Seen by the design requirements, wp < = 0.2π, allow a margin of error of less than 1dB, ws> = 0.3π within attenuation greater than 15dB. In order to verify the actual filtering function of the digital filter design program, the input sequence as validation function x (t) = 4sin (100πt) and x (t) = 4sin (200πt) and x (t) = 4sin (400πt) . And because Ts = 1.25ms, T = 80ms, so the sampling points is 64, that is N = 64, so when M = 6, can debug and validate filtering program.)

是对于运用模糊控制的场合 这些资料极其具有意义(very important docume)

自己编写的LQG/LTR程序，里面附有一片LQG/LTR论文，希望各位能够交流探讨。(LQG/LTR method using MATLAB)

电动机拖动simulink模型，调节pi控制器的参数模拟控制效果，另附程序运行结果图(Drag motor simulink model, adjusting the parameters pi controller analog control results, an additional program to run the results of Figure)

用HOUGH检测直线的时候是两个未知量,因为轴半径和相角可以确定一条直 线，在HOUGH域出现累计最大点就可能是原域中的直线。现在回到圆的检测 上来，确定一个圆需要什么：X坐标，Y坐标，半径三个未知量吧，好了，现在， 你做一个三维空间的HOUGH域，以这三个未知量作为三个轴，现在按照一定步长 进行三重循环，在最内层循环是这样的，X,Y 确定，以不同的半径进行搜索，如 果你的X,Y刚好就是实际图像的X,Y处，半径又搜索到实际真实的半径(The HOUGH detect straight when two unknown amount of axis radius and phase angle can be determined in a straight line, in the HOUGH domain cumulative maximum point may be the straight line of the original domain. Now back to the circle detection up to determine what a circle: X coordinate, Y coordinate, radius three unknowns, now, you do the HOUGH domain of a three-dimensional space, three to three unknown quantity as axis, in accordance with a certain step size triple loop, is such that in the innermost loop, X, and Y determined search for a different radius, If you X, Y, exactly is the actual image of the X, Y, at the radius radius of the search to the actual real)

FEC decoding algorithm for Reed Solomon

基于模糊算法的倒立摆控制的matlab仿真源程序(Inverted pendulum fuzzy control algorithm matlab simulation source based)

this matlab code describes smoothing filter

该压缩包具有35例GUI的设计，主要是带大家入门用的(The archive has 35 cases of GUI design, the main entry is used with all)