Crack-propagation

说明：  基于STM32F103的ST7735s芯片的LCD中文显示例程(LCD Chinese Display Routine Based on ST7735s Chip ST32F103)

LPC2210-user,when you study arm you should use it.(LPC2210-user, when you study arm you should use it.)

PROFIBUS-DP现场总线智能节点的设计程序和源码电路图(Design of intelligent node based on PROFIBUS-DP)

用TI单片机MSP430系列写的CRC检验程序，C语言(Using TI single-chip MSP430 series written by CRC testing procedures, C language)

单片机，通过串行扫描，读取矩阵的键盘码。(Microcontroller reads the keyboard codes.)

ad9850的单片机程序，适用于51系列，有用的可下载参考(ad9850 microcontroller program, suitable for 51 series, useful can be downloaded for reference)

1、掌握利用A/D转换和计算机资源实现示波器的设计方法。 2、设计虚拟示波器。 3、建立NI-DAQmx仿真设备，选择E系列中的NI PCI-6071E数据采集卡的仿真模块，通过DAQmx物理通道识别，产生模拟信号，然后基于LabVIEW开发平台设计实现虚拟示波器。(1, master the use of A/D conversion and the design method of the computer resources to realize the oscilloscope. 2, the design of virtual oscilloscope. 3, establishment of NI- DAQmx simulation equipment, select the NI PCI- 6071- E E series simulation module of data acquisition card via DAQmx physical channel identification, produce analog signal, and then design the virtual oscilloscope based on LabVIEW development platform.)

0.96OLED stm32官方代码 0.91寸OLED显示屏+12832液晶屏+显示器件提供程序原理模块(stm32 0.96OLED Official Code and other)

本程序可利用8位单片实验超声波测速，内含数据拟合(The program can use 8 bit single chip ultrasonic velocimetry experiments)

说明：  本实验开机后，先初始化MPU6050，然后利用DMP库，初始化MPU6050及使能DMP，最后，在死循环里面不停 读取：温度传感器、加速度传感器、陀螺仪、DMP姿态解算后的欧拉角等数据，通过串口上报给上位机（温 度不上报），利用上位机软件（ANO_Tech匿名四轴上位机_V2.6.exe），可以实时显示MPU6050的传感器状 态曲线，并显示3D姿态，可以通过KEY0按键开启/关闭数据上传功能。同时，在LCD模块上面显示温度和欧拉 角等信息。DS0来指示程序正在运行。另外,本例程也可以通过USMART调用MPU_Read_Byte/MPU_Write_Byte 等函数,来实现对MPU6050寄存器的读写操作(仅在UPLOAD OFF状态下).(This experiment starts with initializing MPU6050, then using DMP library, initializing MPU6050 and enabling DMP. Finally, it keeps on in the dead cycle. Read: temperature sensor, accelerometer, gyroscope, Euler angle after attitude calculation of DMP and other data, report to PC through serial port (temperature). The sensor of MPU6050 can be displayed in real time by using the upper computer software (ANO_Tech anonymous four-axis upper computer_V2.6.exe). The state curve and 3D posture can be displayed, and the data upload function can be turned on/off by KEY0 button. At the same time, temperature and Euler are displayed on the LCD module. Angle and other information. DS0 to indicate that the program is running. In addition, this routine can also call MPU_Read_Byte/MPU_Write_Byte through USMART Equivalent function to achieve the read-write operation of MPU6050 registers (only in UPLOAD OFF state).)