TD_XY2-100_R0703

NFC协议第一部分，描述了NFC tag 1 通讯协议(NFC protocol first part describes the communication protocol NFC tag 1)

A New Algorithm for Joint Range-DOA-Frequency Estimation of Near-Field Sources

说明：  利用通信系统中调制信号的循环平稳特性,对频谱空洞进行检测,提升频谱感知技术在低信噪比下的性能。实验结果表明:与传统能量检测方法相比,采用循环特征检测方法改善了认知无线电中频谱空洞的检测能力。(Based on the cyclostationarity of modulation signals, spectrum hole is detected, aiming at the improve- ment of the performance of spectrum sensing in low SNR situation. The results show that comparing with the tra- ditional energy detection technique, cyclostationarity-based spectrum sensing technique has greatly improved the detective ability in cognitive radio.)

有关MVB与工业以太网网关的设计与研究，对列车通信网络感兴趣的朋友可以看看(MVB and industrial Ethernet gateway for the design and research on the train communication network interested friends can see)

关于天线原理的PPT。等同于教科书。很全。(PPT of antenna principle.Can be used as teaching book. A complete one.)

说明：  ZTEWelink Wireless Module Driver User Guide for WinCE-V1.2

重点研究 了低信噪比﹑多径瑞利衰落信道条件下，基于高阶累积量的OFDM信号盲识别技 术。提出了利用奇数阶累积量区分OFDM信号与单载波信号的方法，并对基于三 阶和五阶累积量的算法进行了仿真分析。 (﹑ Focus on the low SNR multipath Rayleigh fading channel conditions, based on cumulant OFDM signal blind identification technology. Made a distinction between the use of odd-order cumulants single-carrier OFDM signal with the signal approach, and based on the cumulative amount of third-order and fifth-order algorithm for the simulation.)

多功能电能表通信协议_645-2007.pdf(Multi-function watt-hour meter communication protocol _645-2007.pdf)

争对移动声源采用波束形成进行语音增强，提出一种约束子带波束形成算法。其波束形成器基于一个软约束，其目的是要使波束指向特定的区域即声源方向。而其核心在于首先要进行声源定位，获得尽量准确的方位信息，然后构造软约束条件，用于波束形成。且在此过程中不断跟踪声源的移动情况。在构造的约束条件中，需要知道声源的二维信息，即与麦克风阵列的距离和方向角，“软”体现在对距离和方向角的确定都是在一定范围内的，有待进一步更正。(Between the mobile sound source using beamforming for speech enhancement, a constrained subband beamforming algorithm. Its beamformer based on a soft constraints, the aim is to make the beam point to a specific region that is the direction of the sound source. And its core is the first to sound source location, access to location information as accurately as possible, and then construct the conditions of soft constraints for beamforming. And in the process continuously tracking the movement of a sound source. Structure at the binding conditions, need to know the two-dimensional sound source information, that is, with the microphone array the distance and direction angle, the " soft" embodied in the distance and direction angle of the determination are within the scope must be further corrected .)

主要是实现调制识别，区分几种常用的数字调制信号。含有两个文件夹 其一为特征参数的仿真；其二为正确识别率的仿真。文件夹key feature simulink中： 运行程序会得到各特征参数之间区分图 从图中可看到特征参数的有效性，见图。 文件夹classification rate simulink中：运行main.m文件 可以得到正确识别率 见图。(It is mainly to realize modulation recognition and distinguish several commonly used digital modulation signals. The simulation of two folders is one of the characteristic parameters, and the second is the simulation of the correct recognition rate. In the folder key feature Simulink: The running program will get the validity of the feature parameters that can be seen from the diagram, as shown in the diagram. Folder classification rate Simulink: running the main.m file can get the correct recognition rate.)