app52

说明：  4个纹理分割算法合集+n篇IEEE论文合集 对研究纹理分割的同学来说，很有效(4+ n texture segmentation algorithm Collection collection of research papers IEEE paper texture segmentation students, it is very effective)

直流伺服电机转速 PID控制系统仿真 利用MATLAB中的simulink 对直流伺服电机的转速进行仿真(DC servo motor speed PID control system simulation using MATLAB simulink in the speed DC servo motor simulation)

matlab code for 4-ask modulation

内附收集的几种ldpc代码（编码解码皆有），另有论文及书籍（pdf格式）(Containing a collection of several ldpc code (codec Jieyou), while papers and books (pdf format))

linear acceleration

打开Matlab，输入代码，运行之，出结果(Open Matlab, enter the code, run it, the results)

matlab编程通过MUSIC算法定位声源方向（DOA），图形最高点对应横坐标即为声源方向(MUSIC algorithm matlab programming by positioning the sound source direction (DOA), the horizontal axis corresponds to the highest point of the graphic is the sound source direction)

1、验证窗函数 N 变化时，验证其频谱主瓣副瓣比、主瓣宽度的变化。 a)矩形窗函数的 N 变化时，验证其其频谱主瓣副瓣幅度比基本不会发生变化， 而主瓣宽度将会变窄。这说明，当用矩形窗函数设计滤波器时，增大 N 不能使 得阻带衰减减小，但能够减小过渡带。 b)再选取其他的窗如 hamming/hanning 窗，验证当 N 变化时，其频谱主瓣宽 度变化、主瓣副瓣比值变化情况。 2、用窗函数法设计线性相位 FIR 低通，通带截止频率 wp=0.5PI, 阻带截止频率 ws=0.6PI, 阻带衰减不小于 40dB,通带衰减不大于 3dB. a)选取 Hanning,Hamming 窗查看设计出来的 FIR 的过渡带宽和阻带衰减是否 满足要求，二者有什么不同。 b)使用 hamming 窗，将窗长增大 1 倍，设计 FIR。验证同样的窗函数类型 (hamming)，不同窗长度时，设计出来的 FIR 的过渡带宽和阻带衰减都有什么变 化。 3、不使用 Matlab 系统函数得到上一项指标的低通，并与上一项结果比较。 4 用窗函数法设计线性相位 FIR 高通，通带截止频率 wp=0.8PI, 阻带截止频率 ws=0.7PI, 阻带衰减不小于 30dB,通带衰减不大于 3dB.(An actual filter is implemented using the truncated unit impulse response sequence of the ideal filter. For the ideal low pass filter, the unit impulse response h, N, D () is intercepted by a length of N, and the length is The N sequence H (n), when intercepted, guarantees causality and linear phase requirements for the filter. In order to reduce the Gibbs effect, the H (n) window is added, and the appropriate window function is selected to ensure the stopband attenuation and Transition zone requirement. Note that the sidelobe of the window function affects the stopband attenuation of the filter, and the main lobe width affects the filter Transition bandwidth.)

我们公司控制电动葫芦的程序，是用omron程序编写的．(Electric hoist control of our company s procedures, is prepared by Omron procedures.)

WSN 质心定位算法 Centorid Algorithm 加经典参考文献 A: 如果接受节点接收到的包数目与发送节点发送的包数目的比值大于CM_threshold,则这两个节点视为邻居节点 未知节点利用邻居锚节点进行定位，没有邻居锚节点的未知节点无法定位。 B: 如果接受节点接收到的包数目与发送节点发送的包数目的比值大于CM_threshold,则这两个节点视为邻居节点 未知节点一旦被定位就充当起锚节点的功能，向周围邻居发送自己的估计坐标信息 未知节点把已经定位的未知节点与锚节点同等对待 C: 如果接受节点接收到的包数目与发送节点发送的包数目的比值大于CM_threshold,则这两个节点视为邻居节点 有邻居锚节点的未知节点只利用邻居锚节点进行定位，没有邻居锚节点的未知节点才利用已经定位了的邻居未知节点进行定位。(WSN centroid localization algorithm Centorid Algorithm A: If you accept the received packet node number and the number of packets sent by the sending node ratio greater than CM_threshold, then these two nodes as neighbors Unknown node using the neighbor anchor nodes to locate, no neighbors anchor nodes and unknown nodes can not be located. B:   If you accept the received packet node number and the number of packets sent by the sending node ratio greater than CM_threshold, then these two nodes as neighbors Unknown nodes are positioned on as soon as the function of anchor nodes to send their neighbors estimated coordinate information Unknown unknown node to node already positioned anchor nodes treated equally C: If you accept the received packet node number and the number of packets sent by the sending node ratio greater than CM_threshold, then these two nodes as neighbors Of the unknown neighbor anchor node the neighbor nodes are only positioned anchor nodes, )