-
PCM
说明: 在实际的调谐解调电路中,采用的是非相干载波解调,本振信号与发射端的载波信号存在频率偏差和相位抖动,因而解调出来的模拟I、Q基带信号是带有载波误差的信号。这样的模拟基带信号即使采用定时准确的时钟进行取样判决,得到的数字信号也不是原来发射端的调制信号,误差的积累将导致抽样判决后的误码率增大,因此数字QPSK解调电路要对载波误差进行补偿,减少非相干载波解调带来的影响。(In the actual tuning and demodulating circuit, non-coherent carrier demodulation is adopted, and the frequency deviation and phase jitter of the local oscillator signal and the carrier signal of the transmitting end are present, and thus the demodulated analog I and Q baseband signals are signals with carrier error.)
- 2019-01-30 20:16:08下载
- 积分:1
-
cc2430tocc2530migrationguide
application node 071 cc2430 to 2530 immigigration guide
- 2010-01-23 21:49:50下载
- 积分:1
-
实验指导书第一部分
说明: 通过几个图文示例,详细说明了如何在matlab上通过虚拟串口发送和接受数据(Through a few graphic examples, detailed description of how to send and receive data through virtual serial port on matlab)
- 2020-04-20 17:02:25下载
- 积分:1
-
LFM
说明: 脉冲压缩的匹配滤波。目标距离分别为10米,30米和100米,对于未压缩的脉冲,三个回波信号混叠在一起,不能分辨,而经过脉冲压缩的脉冲信号则可通过匹配滤波收到3个回波信号(Matched filtering for pulse compression.Target distances are 10 metres, 30 metres and 100 metres, respectively. For uncompressed pulses,The three echo signals are overlapped and can not be distinguished. While pulse compression can distinguish three echo signals after matched filtering)
- 2021-04-15 20:38:54下载
- 积分:1
-
PLL
锁相环问题的仿真,可以解决数字锁相环的仿真问题(Phase-locked loop simulation problem, can solve the problem of digital phase-locked loop simulation)
- 2009-05-23 01:14:31下载
- 积分:1
-
Meng-mdp
Two different types of measurement matrices: predefined and random measurement matrices were studied and tested using MATLAB. The speech signal was reconstructed without losing important information in order to achieve an increase in the data rates. After multiple simulations
- 2012-12-18 12:52:19下载
- 积分:1
-
载波同步仿真,使用的是反馈补偿法
说明: 载波同步仿真,使用的是反馈补偿法,接收信号经补偿矩阵,误差提取,环路滤波,相位累加器后反馈回补偿矩阵,稳定后估计相位趋近相位差,存在相位模糊情况。(the simulation of the carrier synchronization)
- 2020-04-30 12:55:40下载
- 积分:1
-
BER
这是一个matlab和optisystem联合调试用的误码率计算程序,里面的文件报过一个可以用optisystem7和optisystem13可以打开的OSD仿真图,还有一个MATLAB计算BER的程序。给出了如何设置系统的大纲。从OptiSystem的电信号输入到Matlab组件。当OptiSystem运行时,它将调用Matlab组件中的M文件,处理数据,然后将所得的电信号导出回OptiSystem。然后将输出信号连接到BER分析仪。经过我调试,文件齐全,放心下载(The attached image gives an outline of how the system should be setup. You should start with inputting the electrical signal from OptiSystem into a Matlab component. When OptiSystem runs, it will call the M-file in the Matlab component, process the data, and then export the resulting electrical signal back into OptiSystem.The output signal is then connected to the BER Analyzer.)
- 2021-03-18 15:39:20下载
- 积分:1
-
ZYOU
电脑串口控制西门子s7-200程序,可以通过电脑直接控制PLC(Computer serial port control of Siemens S7-200 program)
- 2013-08-11 20:37:28下载
- 积分:1
-
ldpc-a-brief-tutorial
LDPC Codes – a brief Tutorial
Bernhard M.J. Leiner, Stud.ID.: 53418L bleiner@gmail.com
April 8, 2005
- 2011-06-02 15:26:08下载
- 积分:1