MDS-MAP

直接序列扩频通信系统，快速傅里叶变换的matlab程序(Direct sequence spread spectrum communication systems, fast Fourier transform matlab program)

本仿真为电源充电仿真，采用了boost电路(The simulation for power charging simulation, using a boost circuit)

matlab code for compressed sensing

说明：  支持向量机libsvm分类 林智仁(Lin Chih-Jen)的工具箱 一看便学会了怎么用libsvm。(a good m file!a gooa good m file!d m file!a good m file!a good m file!)

奥本海姆信号与系统(第二版)及习题答案，还有《信号与系统》计算机练习 利用MATLAB 刘树棠翻译(Oppenheim Signals and Systems (second edition), and exercise answers, and " Signals and Systems" computer exercises using MATLAB Liu Shutang translation)

任务： 1） 借助MATLAB画出误差性能曲面和误差性能曲面的等值曲线（参考PPT2.1第17页的两幅图）； 2） 写出最陡下降法以及LMS算法的计算公式（取 ）； 3） 用MATLAB产生方差为0.05, 均值为0白噪音S(n)，并画出某次采样得到的波形（即产生任意一个噪声随机序列）； 4） 根据 2）中的公式，并利用 3）中产生的S(n)，在 1）中的误差性能曲面的等值曲线上叠加画出采用最陡下降法以及LMS法时H(n)的在叠代过程中的轨迹曲线（参考PPT2.1第17页的右下图的曲线1和曲线2）。 5）用MATLAB计算并画出LMS法时 随时间n的变化曲线（对应S(n)的某一次的一次实现）和e(n)波形； 注意：某一次实现的结果并不能从统计的角度反映实验的结果 的正确性，为得到具有统计特性的实验结果，可用足够多次的 实验结果的平均值作为实验的结果。用MATLAB计算并画出 采用LMS法时，J(n)的100次实验结果的平均值随时间n的变 化曲线（即 生成随机噪声信号并计算结果，重复执行100次， 求平均结果）。 6）在 1）中的误差性能曲面的等值曲线上，叠加画出采用LMS法得到的100次实验中的H(n)的平均值的轨迹曲线； (Task: 1 ) Draw with MATLAB error performance surface and surface contour error performance curve ( refer PPT2.1 two chart on page 17 ) 2 ) Write the steepest descent method and the LMS algorithm formula ( take ) 3 ) Using MATLAB to generate variance of 0.05 with a mean of 0 white noise S (n), and draw a particular sampling waveform ( ie, any noise generated random sequence ) 4 ) based on 2 ) of the formula , and use 3 ) generated in S (n), in a ) the error performance curves superimposed on the surface contour plot using the steepest descent method and the LMS method when H (n) the iterative process in the trajectory curve ( refer PPT2.1 page 17 bottom right of the curves 1 and 2 ) . 5 ) using MATLAB LMS method is used calculate and draw the curve with time n (corresponding to S (n) of a first implementation of a ) and e (n) waveform Note : in a first implementation of the results are not reflected from a statistical point of view of accuracy of the experimental results ,)

matlab good project that fit curve

本程序为一种基于凸优化的OFDM信道估计算法，平滑SLO算法是求解稀疏线性方程组的一种迭代解法，本程序将其应用于OFDM信道估计，取得了较好的信号估计精度以及速度(This procedure is a convex optimization of OFDM-based channel estimation algorithm, smoothing algorithm SLO is sparse system of linear equations to solve an iterative method, the procedure will be applied to OFDM channel estimation, the signal to obtain a better estimation accuracy and speed)

针对信号自适应chirplet分解未知参数多、实现起来比较困难的特点，文献[1]提出了一种新的chirplet分解快速算法。该算法利用计算信号的二次相位函数，得到其能量分布集中于于信号的调频率曲线上的结论，此时通过谱峰检测可同时获得chirplet调频率、时间中心和幅度的估计；然后通过解线性调频技术获得其初始频率和宽度的估计，仿真结果验证了本文算法的有效性。 (For the signal adaptive the chirplet decomposition of unknown parameters to achieve difficult to literature [1] proposed a new fast algorithm for chirplet decomposition. The algorithm makes use of the secondary phase of the calculated signal function, the conclusion focused on energy distribution curve to tune the frequency of the signal by the peak detection chirplet tune frequency, time center and amplitude estimates then by solving chirp technology to obtain the initial frequency and width is estimated that the simulation results demonstrate the effectiveness of the proposed algorithm.)

何恺明在CVPR会议上的最佳论文，基于暗通道先验的单幅图像去雾技术，演讲ppt，以及主要matlab程序 (Ho Kai Ming Best Paper in CVPR meeting, based on a priori dark passage to a single image fog technology, presentation ppt, and the main matlab program)