voicebox

这是一个三次样条插值的.m程序 输入的是一个二维数组A(Nx2) 插值方法为: S(x) = A(J) + B(J)*( x - x(J) ) + C(J)*( x - x(J) )**2 +D(J) * ( x - x(J) )**3 for x(J) <= x < x(J + 1) (This is a cubic spline interpolation. M program input is a two-dimensional array A (Nx2) interpolation method: S (x) = A (J)+ B (J)* (x- x (J ))+ C (J)* (x- x (J))** 2+ D (J)* (x- x (J))** 3 for x (J) )

本程序基于matlab 遗传算法的源程序代码，遗传算法是应用于各种优化问题的典型算法，有很高的参考价值。(procedures based on the Matlab genetic algorithm source code, the genetic algorithm is applied in a variety of typical optimization algorithm, a high reference value.)

这是第二能量熵的matlab代码，MIMO OFDM matlab仿真,使用高阶累积量对MPSK信号进行调制识别。( This is the second energy entropy matlab code, MIMO OFDM matlab simulation, Using high-order cumulants of MPSK signal modulation recognition.)

此为matlab函数库，种类齐全，可供用matlab仿真的开发者使用。(malab data)

本文提出了一种适用于低轨卫异扩频通信系统的多普勒频移快捕方法.该方法基于数字匹配滤波器及自动频率控制环路_利用数字匹配滤波器的囚码快捕特性及其输出主相关峰值对频偏的敏感性，缩短多普勒频移的 捕获时间.论文首先推导了多普勒频移的平均捕获时间表达式，然后根据数值分析结果得到了准最佳捕获判决策略，最后通过比较验证了该快捕方法相对于传统串行捕获方法在性能上的提高. (This paper presents a low-orbit health for different spread spectrum communication system fast catching the Doppler shift method, which based on digital matched filter and automatic frequency control loop _ prisoners using digital matched filter code features rapid acquisition and the output of the main correlation peak frequency deviation of the sensitivity of the Doppler frequency shift to shorten acquisition time. paper first derive the mean Doppler shift acquisition time expression, then the numerical results obtained quasi-optimal capture decision strategies, and finally verified by comparing with the rapid acquisition method to capture the traditional method of serial improvement in performance.)

Person Identification Using Ear Biometrics

MATLAB m程序编程，实现PID控制中P I D三个控制参数的自动整定(Programming with MATLAB m to realize automatic tuning of PID three control parameters in PID control)

CurveLab is a collection of Matlab and C++ programs for the Fast Discrete Curvelet Transform in two and three dimensions.

相干多径信号波束形成，学习阵列信号处理必用(correlated signls beamforing)

MATLAB遗传算法工具箱及应用。本书系统介绍MATLAB遗传算法和直接搜索工具箱的功能特点、编程原理及使用方法。全书共分为9章。第一章至第四章介绍遗传算法的基础知识，包括遗传算法的基本原理，编码、选择、交叉、变异，适应度函数，控制参数选择，约束条件处理，模式定理，改进的遗传算法，早熟收敛问题及其防止等。(MATLAB genetic algorithm toolbox and its application. This book describes the features of MATLAB Genetic Algorithm and Direct Search Toolbox, programming principles and use. The book is divided into nine chapters. Chapter to Chapter IV describes the basics of the genetic algorithm, including the basic principles of genetic algorithm, encoding, selection, crossover and mutation, the fitness function, the control parameter selection and processing constraints, schema theorem, improved genetic algorithm, precocious convergence problem and its prevention.)