Sunplus-061-chip-training

430的DS1302的驱动,知识源于网络,(430 of the DS1302-driven, knowledge from the network,)

时间延迟系统的应用，方法和发展趋势，详细介绍了带时延的控制系统的研究理论和方法(Time delay applications, methods and trends systems, detailing the theories and methods of control systems with delay)

led 操作 s3c2440,中断点亮led (English Version English VersionEnglish VersionEnglish Version)

只用于学习STM32F429的ADC，将一路ADC采集，改为两路ADC采集，并将采集的模拟量转换为紫外线等级。(It is only used to learn the ADC of STM32F429. It changes one ADC acquisition to two ADC acquisitions, and converts the analog acquisition to ultraviolet level.)

ATK-HC05蓝牙串口模块的使用，实现蓝牙串口通信(Using ATK-HC05 Bluetooth Serial Port Module to Realize Bluetooth Serial Port Communication)

电商毕设小项目，希望对新手能有所帮助，高手就别下载了(simple project)

说明：  在此基础上，设计一种温度测量系统，能够检测温度，并通过按键调整温度的上下限值，若超过该限值，进行报警提示。该系统的硬件子电路主要用Protues仿真软件实现，具体的子电路包括：恒流源电路（TLC2543芯片）、信号放大调理电路（两线制铂电阻PT100）、单片机最小系统（AT89C51）、A/D转换电路、按键电路、显示电路、声光报警器等。该系统的软件电路以C语言为基础，在Keil中实现。最后通过软硬结合，实现电路的各种情况仿真，以此验证电路设计的正确性和合理性。(On this basis, a temperature measurement system is designed, which can detect the temperature and adjust the upper and lower limits of the temperature by pressing the key. If it exceeds the limit, an alarm will be given. The hardware sub circuit of the system is mainly realized by Proteus simulation software. The specific sub circuits include: constant current source circuit (TLC2543 chip), signal amplification and conditioning circuit (two-wire platinum resistance PT100), minimum system of single chip microcomputer (AT89C51), a / D conversion circuit, key circuit, display circuit, sound and light alarm, etc. The software circuit of the system is based on C language and implemented in keil. Finally, through the combination of hardware and software, the circuit simulation is realized to verify the correctness and rationality of the circuit design.)

说明：  这是在单片机上实现的射击训练游戏,仿真结果直观！(This is implemented on the microcontroller fire training games, visual simulation!)

lm8962模拟I2C的程序,可以参考下(the lm8962 simulation I2C procedures, refer to the following)

本实验将实现如下功能：开机的时候先检测SD卡和SPI FLASH是否存在，如果存在则获取其容量，并显示在LCD上面（如果不存在，则报错）。之后开始USB配置，在配置成功之后就可以在电脑上发现两个可移动磁盘。我们用DS1来指示USB正在读写，并在液晶上显示出来，同样，我们还是用DS0来指示程序正在运行。(This experiment will achieve the following functions: when booting, first detect the existence of SD card and SPI FLASH, and if there is, obtain its capacity, and display it on the LCD (if not, report an error). Then the USB configuration is started, and after the configuration is successful, two removable disks can be found on the computer. We use DS1 to indicate that the USB is reading and writing, and display it on the LCD. Similarly, we use DS0 to indicate that the program is running.)