-
BeamFroming
自适应波束形成(智能天线)的MATLAB代码仿真程序(Adaptive beamforming (smart antennas) code of the MATLAB simulation program)
- 2009-04-23 09:14:13下载
- 积分:1
-
qtks
matlab在气体扩散中的应用,利用matlab求解气体扩散中的数学模型。(matlab in the application of gas diffusion in)
- 2011-08-21 20:22:56下载
- 积分:1
-
readPLYfile
this code is use to read ply file
- 2013-10-04 19:05:09下载
- 积分:1
-
OPTI-master
OPTI open resource from their website
- 2020-06-23 07:00:01下载
- 积分:1
-
ran
ran资源网络程序 (Resource Network program ran)
- 2009-03-17 19:22:41下载
- 积分:1
-
AVR001
das filter: baswed on research by das in filtering
- 2009-05-25 19:31:39下载
- 积分:1
-
MSE
多尺度样本熵,研究信号用的,基础知识,非常重要(MSE, Multi-scale sample entropy, the basic knowledge of signal research, is very important)
- 2018-08-01 09:10:41下载
- 积分:1
-
fangzhen
一本关于控制系统仿真的书的程序
1、文件夹1中的程序是书中的一些仿真。
2、文件2中的是最近做的预测控制、PID控制及逻辑控制的对比综合研究。
3、文件夹3中是与maltab通信的数据采集板的设计文件。包括串口设计、USB1.1及USB20设计。这是最新的设计资料,很有参考价值。
(About a control system simulation procedure one book, folders, one in the book are a number of procedural simulation. 2, document 2 are recent to do predictive control, PID control and logic control study Comparative General. 3, folder 3 are maltab communication with data acquisition board design document. Including the serial design, USB1.1 and USB20 Designed. This is the latest design information, useful reference value.)
- 2009-03-18 22:36:23下载
- 积分:1
-
zydu-matlab
用 MATLAB实现作业车间调度的遗传算法源程序,基本思路可供参考。希望对大家有所帮助。( Realization of job-shop scheduling based on genetic algorithm by using MATLAB soft. wish help to others.)
- 2010-10-15 08:41:33下载
- 积分:1
-
three_dim_plot
The model used for creating the reference voltage is shown
in Fig. 4. First, photovoltaic output current (Ipv) and output
voltage (Vpv) are passed through a first order low pass filter
with a magnitude of G = 1 and a time constant of T = 0.01
seconds in order to filter out the high frequency components
or harmonics from these signals as shown in Fig. 5 and Fig. 6.
The filtered current and voltage signals (Ipv_F and Vpv_F) are
then fed into the MPPT control block that uses the Incremental
Conductance Tracking Algorithm. An algorithm that is based
on the fact the slope of the PV array power curve shown in
Fig. 7 is zero at the Maximum Power Point (MPP), positive on
the left of the MPP, and negative on the right. The MPP can
thus be tracked by comparing the instantaneous conductance
(I/V) to the incremental conductance (∆ I/∆ V) [11] as in (1):
- 2013-07-23 17:56:06下载
- 积分:1