ftcs-code

隐式及显示技术模拟复合材料结构的固化，UMAT程序(Cure Simulation of Composite Structures Applying Implicit and Explicit FE Techniques)

基于递推最小二乘法进行系统辨识的基本原理,对给定的实际输入输出数据运用MATLAB的M语言编写递推最小二乘算法(The basic principle of system identification based on recursive least squares method, using the MATLAB M language to write recursive least squares algorithm for given actual input and output data)

植被指数计算程序，共计算了31个植被指数(Vegetation index calculation program, a total of 31 vegetation index calculations)

基于模式耦合方法建立三维面波传播模型，该代码对于做波场模拟的同学很有用。(This program calculates the wavefield produced by a monochromatic surface wave mode incoming on a 3D cartesian structure. It is based on mode coupling and multiple scattering.)

描述固体凝固的随机变化状态，为fortran语言，请自行下载对应编译器(describe solid phase status, as fortran lauguage, please download associated compiler)

FCT_VOF AND YOUNGS_PLIC fully functioning source codes Debugged and fully functioning source codes Both can be used to calculate by choosing the icase for (1) the Zalesak rotational flow problem (2) the shear flow problem This complete set includes both FCT_VOF and Youngs_plic source code in f90. Including a input data file. The codes have been debugged and tested using MS-FORTRAN. Results can be obtained directly from the output files and loaded to get results. (FCT_VOF AND YOUNGS_PLIC fully functioning source codes Debugged and fully functioning source codes Both can be used to calculate by choosing the icase for (1) the Zalesak rotational flow problem (2) the shear flow problem This complete set includes both FCT_VOF and Youngs_plic source code in f90. Including a input data file. The codes have been debugged and tested using MS-FORTRAN. Results can be obtained directly from the output files and loaded to get results. Ps: statement CALL WRITER needed to be removed and replaced with usual output statement fsuch as: Write(*,*) x(I,j),y(I,j),fi(I,j)…. Etc., for user’s requirement. )

高斯拟合程序，采用高斯函数拟合数据，获得拟合高斯函数的平均值和方差。(Gaussian fitting procedure, using Gaussian function fitting the data, fitting Gaussian function to obtain the mean and variance.)

利用FFT估计正弦信号的频率,要估计一个叠加了高斯白噪声的正弦信号 的频率 ，可以通过对x(n)做傅里叶变换，得到频谱图，找出幅度的最大值对应的频率值 ，进行多次变换，求出均方误差 。改变信噪比SNR，通过仿真可以得出随着信噪比增加，均方误差减小。(Sinusoidal signal using FFT frequency estimation, to estimate a Gaussian white noise superimposed on the frequency of sinusoidal signals, can be achieved by x (n) be the Fourier transform to get spectrum to identify the magnitude of the frequency value corresponding to the maximum , several transformations, find the mean square error. Change the signal to noise ratio SNR, the simulation can be drawn as the SNR increases, the mean square error decreases.)

说明：  实现加权复杂网络的LeaderRank算法(Leaderank algorithm for weighted complex networks)

最小二乘估计法在直流电机参数估计中的一个应用，在只已知输入输出数据的情况下，就可以获得电机的内部参数。(DC motor parameter estimation least squares estimation method, in the case of known input and output data only, you can get the internal parameters of the motor.)