complex-net

本资料是MATLAB教程的课件，传上来与大家共享一下(卤 戮 脳 脢脕脧脢脟MATLAB 陆 脤 鲁 脤渭脛 驴 脦 录 镁 拢 卢 )

该程序用于求单跨梁振型及频率（梁的两端任意约束）(The procedure for seeking a single cross-Liang type and frequency (arbitrary constraints at both ends of beams))

MIMO系统容量仿真程序分为两个。其中 文件夹1为：发射天线数为4，接收天线数逐渐增大时MIMO系统容量的仿真程序。 文件夹2为：接收天线数为4，发射天线数逐渐增大时MIMO系统容量的仿真程序。(MIMO system capacity simulation program is divided into two. One folder 1 as follows: the number of transmitting antennas is 4, gradually increasing the number of receive antenna MIMO system capacity when the simulation program. Folder 2 as follows: the number of receiving antennas 4, gradually increasing the number of transmission antennas, MIMO system capacity when the simulation program.)

kriging响应面模型，该程序可以进行函数的拟合，精度很高 (kriging model)

matlab超分辨率重建,对比相应的论文看，很好理解，可以对图像进行分层，并重建(Matlab super-resolution reconstruction, compared with the corresponding paper, is easy to understand, the image can be layered, and reconstruction)

运用神经网络实现病害诊断.一种基于模糊Hopfield网络的多病害诊断方法(The use of neural networks to achieve disease diagnosis. Hopfield network based on fuzzy multi-disease diagnostic methods)

精通matlab7入门书籍，做数模或者很多方面都需要用到(Proficient matlab7 introductory books and do a few modules, or many aspects need to use)

use a three order loop to track the GPS L2C signal, could be useful for beginner

介绍了平均电流控制型 PFC Boost 变换器的结构， 分析了其工作原理。 分别采用 Power System 工具箱和考虑电感电流断续工作状态的 C-MEX 文件 S 函数建立了主电路模型，对平均电 流控制型 PFC Boost 变换器进行了仿真。仿真结果表明，与 Power System 工具箱模型相比，基于 C-MEX 文件的 S 函数仿真模型能够准确仿真电流断续工作状态，仿真速度快。设计了电路样机进 行了实验研究，仿真结果与实验结果一致，证明了该方法的正确性。利用该方法可以高效地仿真 研究系统结构和参数变化时性能变化情况，得到的平均电流控制型 PFC Boost 变换器的混沌分岔 图，为更好地理解和设计这种变换器提供了有利的工具。(The structure of average current controlled power factor correction (PFC) Boost converter is introduced, and its working principle is analyzed. The PFC Boost converter is simulated using the model established with Power System toolbox and the C-MEX file S-function model respectively. Simulation results show that the C-MEX file S-function model can simulate the all state of the converter including discontinuous conduction mode with high speed. Experimental results show the correctness of the simulation results and the proposed method. The method is suitable for simulation the performance changing with the variation of system structure or parameters. The bifurcation diagram is derived for PFC Boost converter using this method, which is very useful for better understanding and better design of the converter.)

利用Harris角点检测算法很好的程序，通过互相关算法检测角NCC配准(Good program using Harris corner detection algorithm, detect corner through cross-correlation method for NCC registration)