登录
首页 » LabView » as

as

于 2014-09-30 发布 文件大小:30KB
0 297
下载积分: 1 下载次数: 2

代码说明:

说明:  Labview汽轮机振动监测源代码,对信号进行倒频谱分析(Labview example)

文件列表:

汽轮机振动监测-倒频谱分析.vi,38229,2014-03-30

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • 拉力传感器电机控制
    说明:  数据采集卡采集拉力值,与预先设定的拉力值进行比较,然后PID运算,控制相应的PWM占空比输出,最终控制电机的速度(The data acquisition card collects the pull value and compares it with the pre-set pull value. Then the PID arithmetic is used to control the output of the corresponding PWM duty cycle, and finally the speed of the motor is controlled.)
    2020-06-17 02:00:01下载
    积分:1
  • New folder (3)
    说明:  this folder contains VIs related to USRP.
    2019-06-08 22:23:44下载
    积分:1
  • 温湿度传感器
    运用Labview实现温湿度传感器的应用,方便快捷,简单实用。(Using Labview to realize the application of temperature and humidity sensor is convenient, fast, simple and practical.)
    2019-01-14 08:35:19下载
    积分:1
  • 多通道温度监测系统
    说明:  由于采集温度并可以对温度实时监测,同时多通道采集温度,对温度超过限度时采取报警措施。(Data Acquisition Program)
    2019-05-18 21:10:39下载
    积分:1
  • HOMEWORK
    用LabVIEW编制一个完整应用软件,完成以下功能: 1、产生一个正弦波,叠加一个噪声信号,从界面上可以调整噪声和信号的幅度、频率等参数,此信号作为后续分析的信号源; 2、显示信号的时域波形,点击按钮可以显示信号的幅度谱、功率谱 3、图形上可以显示光标,具有峰值跟踪功能,同时将峰值频率、幅度显示在界面上。 4、点击按钮可以计算显示信号的失真度(THD)、信噪比(SNR)、各次谐波的频率和幅度;(Preparation of a complete application using LabVIEW software, perform the following functions: 1, generates a sine wave, the superposition of a noise signal, the interface can be adjusted from the noise and the signal amplitude, frequency and other parameters, this signal as a follow-up analysis of the signal source 2. time-domain signal waveform display, click the button to display the signal amplitude spectrum, power spectrum 3, you can display a cursor on the graph, with a peak tracking, while the peak frequency, amplitude displayed on the screen. 4, click the button to display the calculated distortion (THD) signal to noise ratio (SNR), each harmonic frequency and amplitude )
    2014-05-28 21:23:57下载
    积分:1
  • UsingTheProgramToGenerateAtriggerEvent
    labview中用程序去产生一个触发事件是个难点,相关的介绍和例子并不多,本程序使用值属性信号结点改变的方法去产生一个事件,实现程序控制产生触发事件的功能,labview开发版本8.2。(labview using the program to generate a trigger event is difficult, relevant examples of the introduction are not many,here we use the value change of the node attribute of the signal to generate an event, the realized the program control functions to generate trigger events, the version of labview development is 8.2 .)
    2009-04-15 02:58:25下载
    积分:1
  • 二进制文件读取
    利用Labview软件编写读取二进制文件程序(The Labview program reads the binary file)
    2018-05-22 20:03:20下载
    积分:1
  • 自适应屏幕分辨率
    说明:  可以帮忙LabVIEW界面,自适应屏幕分辨率(Screen adaptive resolution)
    2021-01-29 15:27:05下载
    积分:1
  • Example_BP Network_Classification
    说明:  通过LabVIEW平台搭建BP神经网络模型(BP Neural Network Model Based on LabVIEW Platform)
    2019-03-15 16:26:49下载
    积分:1
  • String Hex to DBL
    16进制字符串转十进字符串制显示labview(Hex to decimal conversion)
    2018-12-24 09:50:59下载
    积分:1
  • 696516资源总数
  • 106914会员总数
  • 0今日下载