matlab-PCA

一款很好用的MATLAB程序,运行会可以从清楚 的图形中看到结果(A good use of MATLAB procedures, will run from clear to see the results of graphics)

说明：  实现了求ARMA模型的两种算法，用matlab实现(ARMA model for the realization of the two algorithms, with the realization of matlab)

gaussian mixture model with EM algorithm Matlab code

rectangular qam simulink

blowfis and ecb encription

MATLAB是一套功能十分强大的工程计算及数据分析软件,具有友好的可视化编程界面及接近数学表达式的自然化语言。针对信号与系统中傅里叶变换具有抽象度高、难于理解的特点，利用MATLAB强大的信号处理功能、阶跃响应，微分方程，卷积定理的内容，通过MATLAB 程序实现。本文介绍了MATLAB在信号与系统仿真中的应用,该软件在通信电子类课程中应用越来越广泛,通过几个典型实例来重点研究。 关键词：MATLAB；阶跃响应；微分方程；卷积；信号与系统；仿真 (MATLAB is a very powerful engineering calculations and data analysis software, with a friendly interface and visual programming language close to naturalizing mathematical expressions. For the Fourier transform of signals and systems with a high degree of abstraction, it is difficult to understand the characteristics, the use of the powerful MATLAB signal processing functions, step response, convolution theorem content differential equations by MATLAB program. This article describes the application of MATLAB in signal and system simulation, the software in the electronic communications courses in applied more widely, by focusing on a few typical examples. Keywords: MATLAB step response signals and systems convolution differential equation simulation )

说明：  任务：设计一个4×2.5Gbit/s 长距离光纤传输系统，并利用OptiSystem 仿真验证。 要求： 1．采用波分复用技术，波长设置以100GHz 为间隔，频率分别为193.1THz、193.2THz、193.3THz、193.4THz，每个波长传输速率为2.5Gbit/s（NRZ），传输距离为300km。采用常规光纤，光纤损耗系数为0.25dB/km。 2．单通道光发送机最大输出功率为0dBm，光接收机的接收光功率不低于－26dBm，过载点为－10dBm。 3．可以采用EDFA 作为线路放大器，其中EDFA 的输入功率限制在－18～2dBm，最大输出功率20dBm，增益范围为13～25dB，噪声指数4.0dB。(Task: Design a 4 x 2.5 Gbit/s long-distance optical fiber transmission system, and use OptiSystem simulation to verify. Requirement: 1. Using wavelength division multiplexing technology, the wavelength is set at 100GHz intervals, with frequencies of 193.1 THz, 193.2 THz, 193.3 THz and 193.4 THz, respectively. The transmission rate of each wavelength is 2.5 Gbit/s (NRZ), and the transmission distance is 300 km. The loss coefficient of conventional optical fibers is 0.25dB/km. 2. The maximum output power of a single-channel optical transmitter is 0 dBm, and the receiving power of an optical receiver is not less than -26 dBm, and the overload point is -10 dBm. 3. EDFA can be used as line amplifier, where the input power of EDFA is limited to - 18-2dBm, the maximum output power is 20dBm, the gain range is 13-25dB, and the noise index is 4.0dB.)

One program to simulation light passing through a glass sphere. It is interesting and can be used in geometric optics.

Basic matlab source codes

matlab 子程序集：The routines supplement the book, "Numerical Methods for Physics", 2nd Ed. (Prentice Hall).(matlab subroutine sets: The routines supplement the book, " Numerical Methods for Physics" , 2nd Ed. (Prentice Hall).)