include

msp430f5438系统中文资料(全)(msp430f5438system_Chinese Materials)

使用89S52单片机对DS18B20进行驱动，在数码管上显示当前温度。(DS18B20 using 89S52 microcontroller to drive on, in the digital pipe display the current temperature.)

这是一个用51单片机系统仿真ucosii工作的protues电路 本系统包括扩展64k RAM的单片机系统和杨屹移植到51单片机的ucosii 系统 使用方法： 1.安装Protues7.4版，然后用protues打开protues 8051 simulation 文件夹 中的extern ram.DSN 文件 2.打开extern ram.DSN 后，双击单片机在弹出的窗口中的Program File 选项 中选择yy.hex文件。 (yy.hex其实就是yy文件夹中keil文档编译出来的hex文 件，yy文件夹是杨屹的ucos51 系统，用keil 2 可以打开) 3.在Clock Frequency选项中输入22.184M(杨屹的ucos51 用的是22.184M hz的单片机频率) 4.双击VTERM串口调试显示屏，在Baud Rate 选项中选择19200的波特率 5.保存，点击运行就可以看到经典的hello world 了。 (1. Protues7.4 version installed, and then open the protues folder protues 8051 simulation The extern ram.DSN file 2. Open extern ram.DSN, double-click the pop-up window of SCM in the Program File option, select yy.hex file. (yy.hex actually yy folder keil out of the document compiled hex files, yy folder is Yang Yi s ucos51 system, using keil 2 Can open) 3. In the Clock Frequency option to enter 22.184M (Yang Yi of the ucos51 using a microcontroller 22.184M hz frequency) 4. Double-click VTERM serial debug display, in the Baud Rate select 19200 baud rate options 5. Save, click Run you can see the classic hello world)

水循环系统、温度信号采集系统、制冷及制热系统、内嵌体温调节算法的温度主控单元软件编写，基于atmega128(Water cycle system, temperature signal acquisition system, cooling and heating system, inline thermoregulatory algorithm of temperature control unit writing software, based on the atmega128 )

上位机发送数据包，下位机实现简单数据接，然后可以存储到其他位置(PC to send data packets, lower machine simple data connection, which can then be stored in a different location)

松下车载碟机的协议代码，用于多种汽车的原车配备机头的扩展协议(Panasonic Car turntables protocol code, the original car used in a variety of vehicles equipped with head of the extended protocol)

使用MSP430操作12864显示屏，共显示四行。可显示中文汉字(Use MSP430 operation 12864 display four lines total. Can display Chinese characters)

此程序为4*4矩阵键盘，键盘自身不带电源电阻，八个接线，在程序中进行需进行软件拉高拉低以便按键扫描。 应用单片机为MSP430F5529。(4* 4 matrix keyboard without power resistors MSP430F5529)

本程序利用51单片机的定时器中断产生时间信号，同时具有通过按键调节时间的功能，还可设置闹钟(This procedure using 51 single-chip timer interrupt time signal, but also has the functions via buttons adjust the time, but also set the alarm)

说明：  采用4路红外对管进行循迹，电机控制小车运动。(Four infrared channels are used to track the tube, and the motor controls the motion of the car.)