EEMD

这是一个在labview上根据悬臂梁厚，梁长，受力点距固定端的长度，应变片距固定端的长度，以及应变片上的数值来测算梁的最大挠度的程序。( This is a distance in the labview according thick cantilever beam length, the length of the pitch by the force of the fixed end, the fixed end of the length of the strain gauge and strain values on-chip to measure the maximum deflection of the beam of the program.)

说明：  虚拟仪器的网络控制 1）、设计一个程序控制8个外设小灯的点亮方式，要求两种方式A:每个小灯间隔时间T，依次亮，时间T可调，并循环。B：先1.3.5.7.9亮隔时间T，2.4.6.8.10亮，并循环，T可调。 2）、要求主面板与硬件的8个小灯同步。 3）、通过网络在另一台计算机上控制此程序的运行（利用LabVIEW的DateSocket技术）((Network control of virtual instruments 1), design a program to control eight peripheral lights lit the way, the requirements in two ways A: each light interval T, followed by bright, time T adjustable, and circulation. B: first 1.3.5.7.9 bright every time T, 2.4.6.8.10 light, and circulating T-adjustable. 2), requires eight small lights of the main panel and hardware synchronization. 3), through the network control of this program running on another computer (using the LabVIEW DateSocket technology)))

Labview 电机矢量控制程序以及3-2 3-2坐标变换程序(the labview motor FOC and Park transform)

使用usrp n210,利用Labview实现正弦信号收发，一方面可以利用labview实现实际信号在空中收发，另一方面可以检验设备正常运行。(Using USRP N210 and Labview to transmit and receive sinusoidal signals, on the one hand, it can use LabVIEW to transmit and receive actual signals in the air, on the other hand, it can check the normal operation of the equipment.)

说明：  基于labview的modbus通讯范例(Modbus communication paradigm based on LabVIEW)

说明：  1）、设计一个程序控制8个外设小灯的点亮方式，要求两种方式A:每个小灯间隔时间T，依次亮，时间T可调，并循环。B：先1.3.5.7.9亮隔时间T，2.4.6.8.10亮，并循环，T可调。 2）、要求主面板与硬件的8个小灯同步。 3）、通过网络在另一台计算机上控制此程序的运行（利用LabVIEW的DateSocket技术）((Network control of virtual instruments 1), design a program to control eight peripheral lights lit the way, the requirements in two ways A: each light interval T, followed by bright, time T adjustable, and circulation. B: first 1.3.5.7.9 bright every time T, 2.4.6.8.10 light, and circulating T-adjustable. 2), requires eight small lights of the main panel and hardware synchronization. 3), through the network control of this program running on another computer (using the LabVIEW DateSocket technology)))

LABVIEW与欧姆龙通信，读写寄存器的数据(Communication between LABVIEW and Omron)

labview报表工具包及实例，方便labview程序及界面的打印、输出报告等。(labview toolkits and examples of statements, convenient interface labview program and print output reports.)

从USB串口读取GPS经纬度信息，调用百度地图显示当前位置(Read the GPS latitude and longitude information from the USB serial port, and call the Baidu map to show the current position)

labview环境下的CAN总线上位机模块，使用的CAN 卡为周立功usbcan(CAN bus PC in labview environment, CAN card for ZLG)